When your Siemens dryer starts acting up, the first thing that might come to mind is panic. But, before you get too worried, it’s important to know that many times, these issues come with error codes that are there to help you. These codes are basically the language your dryer uses to tell you what’s wrong. Although they might seem confusing at first, understanding them is easier than you think.
At codigodeerror.com, we know how important it is for you to solve these issues quickly and efficiently. That’s why we’ve prepared a table with the most common error codes you might encounter on your Siemens dryer, along with their description and suggested solutions. Before we dive into details, let’s clarify some concepts that might be new to you:
- Display: It’s the screen on your dryer where error codes are shown.
- AquaStop: A safety system that prevents flooding by detecting water leaks.
- Reset: Turning your appliance off and on to try and solve the problem.
Now, here’s the table with the error codes:
| Error | Description | Cause | Solution |
|---|---|---|---|
| Error codes and symbols on the display | How to solve it | More information | |
| E00 | Turn off the appliance, wait 5 seconds, and turn it back on. If the indication appears again, contact Siemens Service. | ||
| E10 | Turn off the appliance, wait 5 seconds, and turn it back on. If the indication appears again, contact Siemens Service. | ||
| E16 | The door is not closed properly. There may be clothes caught in the door. | Open and close the door again and press the start button again. If necessary, apply some pressure to close the door or remove some garments and close the door again. You can also try turning off and on the washer, select and start the program again. | |
| E17 | Water supply time exceeded. The water supply is not correct. | Check the water pressure directly at the tap using a bucket. About 10 liters of water per minute should flow from the fully open tap. If the water pressure is too low, contact the installer. Also, check the water inlet filters to the supply or if the AquaStop hose is clogged. | |
| E20 | Unexpected heating. | Reset by turning off and on the appliance again. | |
| E29 | Problem with water inlet. | Check the water pressure directly at the tap using a bucket. About 10 liters of water per minute should flow from the fully open tap. If the water pressure is too low, contact the installer. Also, check the water inlet filters to the supply or if the AquaStop hose is clogged. Clean the water supply hose filters. | |
| E32 | “The washer alternately flashes “”end”” when the program finishes.” | It’s not an error. The unbalanced load detection system has interrupted the spin cycle because the garments are unevenly distributed. Distribute small and large items throughout the drum. | |
| E33 | Excess foam detected. | Reduce the amount of detergent in the next wash cycle. Especially in soft water areas and when washing only with very little dirt, the amount of detergent should be reduced accordingly. | |
| E34 | The door has not been closed properly. | Close the door properly (you’ll hear a click). An overly large load may prevent the door from closing properly. Also, check that no garments are trapped between the door and the cover. Restart the program. | |
| F16 | The door is not closed properly. There may be clothes caught in the door. | Open and close the door again and press the start button again. If necessary, apply some pressure to close the door or remove some garments and close the door again. You can also try turning off and on the washer, select and start the program again. | |
| F17 | Water supply time exceeded. The water supply is not correct. | Check the water pressure directly at the tap using a bucket. About 10 liters of water per minute should flow from the fully open tap. If the water pressure is too low, contact the installer. Also, check the water inlet filters to the supply or if the AquaStop hose is clogged. | |
| F20 | Unexpected heating. | Reset by turning off and on the appliance again. | |
| Symbol of a tap | The water pressure is too low or the inlet hose is clogged or bent. | Check the water pressure directly from the tap with a bucket. If the water pressure is too low, contact the installer. Check that the supply hose is not twisted or bent. |
Our advice
Before calling the technical service, we recommend checking this table and following the suggested solutions. Many times, problems can be solved simply without the need for professional assistance. Remember, your Siemens dryer is designed to make your life easier, and with a little knowledge, you can keep it running perfectly.
Error codes in Siemens dryer
Troubleshoot error code “Symbol of a tap” in Siemens drying machine
Troubleshoot error code “F20” in Siemens drying machine
