Errors or Error Codes for Haier Washing Machine

When your Haier washing machine starts acting up, the first thing you should do is check if it’s displaying any error codes on its screen. These codes are the way the appliance specifically communicates what’s going wrong or what needs attention. Though they might seem confusing at first, understanding them is key to troubleshooting issues and keeping your washing machine running smoothly.

In this article, we present a complete table of error codes for Haier washing machines, along with their descriptions, possible causes, and recommended solutions. Before we dive into the table, let’s clarify some concepts that might be new or technical for you:

Drainage: Refers to the process of removing water from the washing machine’s drum. If there are issues with drainage, water might not exit properly.
Temperature Sensor: A component that measures the water’s or the washing machine’s interior temperature. If it’s poorly connected or damaged, it could affect your washing machine’s operation.
Heating Coil: This element heats the water inside the washing machine. If damaged, the desired temperature might not be reached.
Overheating: Occurs when the washing machine or a specific component within it heats up more than what’s safe or intended.
Protection Level: Refers to built-in safety measures to prevent water damage or electrical failures.

Now that we’ve clarified these terms, here’s the table of error codes for your Haier washing machine:

Error	Description	Cause	Solution
1	The door is not properly closed		Close the door correctly.
1	The door lock light is off	The door is not properly closed	Close the door properly
2	“Drainage error, water did not go down for 4 minutes”		“Clean the filter and check that the drain hose is not blocked. If the error persists, contact service personnel.”
2	The door lock lamp flashes 2 times and stops for 4 seconds	“Drainage error, water did not go down for 4 minutes”	“Clean the filter and check that the drain hose is not blocked. If the error persists, contact service personnel.”
3	The door lock lamp flashes 3 times and stops for 4 seconds	The temperature sensor is poorly connected or damaged	Contact service personnel
3	The temperature sensor is poorly connected or damaged		Contact service personnel
4	“Damage to the heating battery or laundry overload, causing the set temperature not to be reached at a certain time (This message is displayed at the end of the program).”		Reduce the load and then start washing again or contact service personnel
4	The door lock lamp flashes 4 times and stops for 4 seconds	Damage to the heating coil causes the set temperature not to be reached within a certain time (this message is displayed at the end of the program).	Contact service personnel
5	The door lock lamp flashes 5 times and stops for 4 seconds	The water level was not reached in 8 minutes.	“Make sure the tap is open and the water pressure is normal – If the problem persists, contact service personnel.”
5	The water level was not reached in 8 minutes.		“Make sure the tap is open and the water pressure is normal. If the problem persists, contact service personnel.”
6	The door lock lamp flashes 6 times and stops for 4 seconds	Silicon control damage term	Contact service personnel
7	Overheating protection or motor damage		Contact service personnel
7	The door lock lamp flashes 7 times and stops for 4 seconds	Overheating protection or motor damage	Contact service personnel
8	Water exceeds the protection level		Contact service personnel
8	The door lock lamp flashes 8 times and stops for 4 seconds	Water exceeds the protection level	Contact service personnel
E11	“Water does not enter the sink/tub, or the water flow is small.”	“• The water supply hose is not frozen. • The water supply hose or the metal filter at the water inlet is blocked. • There is no water.”	Check and resolve the issue. Then press the START/PAUSE button once to restart the washing machine.
E12	Water does not drain	“• Drain hose height above 100 mm. • The drain hose is not blocked by fiber cuttings. • Do not drain the hose too long.”	Check and resolve the issue. Then press the START/PAUSE button once to restart the washing machine.
U3	Rotation failure	“• The clothes are too big or too heavy. • Few pieces of clothing to unscrew. • If the quilt folds into a ball.”	“If the clothes are too small, add 2-3 garments, then check the machine, close the door, and press the START/PAUSE button once to restart the machine.”
X	Door opening failure.	• Water temperature exceeded 40°C. • Water temperature did not exceed 40°C during the wash process.	The door will automatically open once the temperature is below 40°C.
—	Washer not functioning at all.		• Check if the power cable is properly connected. • Press the power button. • Press the START/PAUSE button. • Press the PRESET button. • Check for power failures. • Check if the fuse or circuit breaker has tripped.

Our Advice

Before calling the technical service, we recommend reviewing this error code table. Often, the issue can be something simple that you can resolve yourself, saving you time and money. However, if the problem persists after following the suggested solutions, do not hesitate to contact professional technical service.