When your Fagor dryer starts acting up, the first thing you should do is check if it’s displaying any error codes on its screen. These codes are a way for the appliance to communicate specifically what’s failing in its system, allowing you to identify and, in many cases, solve the problem without immediately calling for technical service.
But, what does each code mean? Below, we present a complete table with the most common error codes for Fagor dryers, their description, and recommended solutions. Before proceeding, it’s important to understand some terms that might seem technical:
- TRIAC: It’s a type of electronic switch that controls the flow of power.
- NTC Probe: It’s a type of temperature sensor that varies its electrical resistance with temperature.
- Door Lock: It’s the mechanism that secures the door during the dryer’s operation.
- Electronic Board: It’s the “brain” of your dryer, controlling all its functions.
- Pressure Switch: It’s a sensor that detects water pressure.
- Flow Meter: Measures the amount of water entering the dryer.
| Code | Description | Solution |
|---|---|---|
| C03 | Problem with clothing distribution inside the drum, unbalanced load. | – Check clothing load. – Try to distribute the load inside the drum. – The error may occur with small loads, try filling the drum more than halfway full. – Check motor and its connections. |
| D01 | Problem with water supply. | – Check water pressure at the tap. – Check hose and tap. – Clean the water inlet filter. (see video) – Check solenoid valve, pressure switch, or flow meter, and their wiring and connections. – Check that the drain hose is at the correct height. |
| D02 | Problem with water drainage. | – Clean the drain filter. (see video) – Check drain hoses and tubes. – Check the drainage pump, its connections, and wiring. (see video) – Check pressure switch, its connections, and wiring. |
| D03 | Problem with water heating (heating element). | – Check thermostats and heating element. (see video) – Check thermostat and heating element wiring and connections. – Check electronic board components. |
| D04 | Problem with the motor or its TRIAC. | – Check TRIAC and relay (components of the electronic board that control motor operation). – Check connections in motor and electronic board. – Check main motor components (brushes, tachometer, coils…). (see video) |
| D05 | Problem with NTC sensor (temperature sensor). Open circuit or short circuit. | – Check sensor connections. – Check the sensor. |
| D06 | Problem with blocked drum. | – Check drum rotation manually. – Check that there are no objects or clothes blocking the drum. – Check motor, its connections, and wiring. (see video) |
| D07 | Door lock problem (door interlock). This error may also appear due to a problem in the motor. | – Open and close the door again. – Check the door interlock and its connections. (see video) – Check components and tracks on the electronic board. – Check motor, its connections, and wiring. – Check main motor components (brushes, coils, tachometer…). (see video) |
| D09 | Problem with the program selector. | – Check program selector. – Check electronic board components and tracks. – Programming failure, call technical service. |
| D10 | Overflow or leak problem, (aquastop device activated). | – Check for leaks. – Check device switch at the bottom of the washer. – Dry the water and seal the leak. |
| D17 | Problem with drum positioning sensor. | – Check sensor, its connections, and wiring. |
| D20 | Problem with water inlet distributor. | – Check solenoids responsible for water distribution in the detergent dispenser. – Check solenoid connections and wiring. |
| D21 | Problem with electronic board. | – Check electronic board connections. – Check electronic board tracks and components. – Programming failure, call technical service. |
| D22 | Problem with drying NTC sensor (temperature sensor). Open circuit or short circuit. | – Check sensor connections. – Check the sensor. |
| D23 | Problem with heating during drying (drying element). | – Check thermostats and heating element. – Check thermostat and heating element wiring and connections. – Check electronic board components. |
| D24 | Problem with drying NTC sensor (temperature sensor). Open circuit or short circuit. | – Check sensor connections. – Check the sensor. |
| D28 | Electronic disturbances problems. | – Check power supply, plug, and washer connections. – Check electronic board connections. – Check electronic board tracks and components. – Programming failure, call technical service. |
| D29 | Electronic disturbances problems. | – Check power supply, plug, and washer connections. – Check electronic board connections. – Check electronic board tracks and components. – Programming failure, call technical service. |
| D30 | Electronic disturbances problems. | – Check power supply, plug, and washer connections. – Check electronic board connections. – Check electronic board tracks and components. – Programming failure, call technical service. |
| D31 | Electronic disturbances problems. | – Check power supply, plug, and washer connections. – Check electronic board connections. – Check electronic board tracks and components. – Programming failure, call technical service. |
| D32 | Electronic disturbances problems. | – Check power supply, plug, and washer connections. – Check electronic board connections. – Check electronic board tracks and components. – Programming failure, call technical service. |
| Error | Description | Cause |
| F01 | Problem with water supply. | – Check water pressure at the tap. – Check hose and tap. – Clean the water inlet filter. – Check solenoid valve, pressure switch, or flow meter, and their wiring and connections. – Check that the drain hose is at the correct height. |
| F02 | Problem with water drainage. | – Clean the drain filter. – Check drain hoses and tubes. – Check the drainage pump, its connections, and wiring. – Check the pressure switch, its connections, and wiring. |
| F03 | Problem with clothing distribution inside the drum, unbalanced load. | – Check clothing load. – Try to distribute the load inside the drum. – The error may occur with small loads, try filling the drum more than halfway full. – Check motor and its connections. |
| F04 | Door lock problem (door interlock). | – Open and close the door again. – Check the door interlock and its connections. – Check components and tracks on the electronic board. |
| F05 | Problem with NTC sensor (temperature sensor). Open circuit or short circuit. | – Check sensor connections. – Check the sensor. |
| F06 | Problem with water heating (heating element). | – Check thermostats and heating element. – Check thermostat and heating element wiring and connections. – Check NTC sensor, its connections, and wiring. – Check electronic board components. |
| F07 | Overfilling problem, excess water or foam in the drum. | – Check solenoid valve (water does not shut off). – Check pressure switch or flow meter, and their wiring and connections. – Clean pressure switch tubes and conduits. – Remove excess foam. |
| F08 | Problem with the motor. | – Check connections in motor and electronic board. – Check the main motor components (brushes, tachometer, coils…). |
| F09 | Problem with the motor. | – Check connections in motor and electronic board. – Check the main motor components (brushes, tachometer, coils…). |
| F10 | Communication problem between electronic boards and components. | – Check washer connections and wiring. – Check electronic board components and tracks. – Programming failure, call technical service. |
| F11 | Communication problem between electronic boards and components. | – Check washer connections and wiring. – Check electronic board components and tracks. – Programming failure, call technical service. |
| F12 | Communication problem between electronic boards and components. | – Check washer connections and wiring. – Check electronic board components and tracks. – Programming failure, call technical service. |
| F13 | Problem with flow meter. | – Check flow meter, its connections, and wiring. – Check water pressure at the tap. – Check hose and tap. – Clean the water inlet filter. |
| F14 | Problem with pressure switch (water level) not detected. | – Clean pressure switch tubes and conduits. – Check membrane and pressure switch connections. |
Our Advice
Before proceeding with any repairs, make sure to disconnect the dryer from the power source to avoid accidents. If after following the recommendations the problem persists, it might be time to contact a professional. Remember, at codigodeerror.com, we are here to help you solve your appliance problems in the most efficient way possible.
Error Codes in Fagor Dryers
Troubleshoot error code “F14” in Fagor drying machine
How to eliminate F14 error in Fagor dryer? Error: F14Description: Professor problem (water level) is not detected.Cause: Solution: - Clean tubes and ducts. - Check membrane and prisoner connections. More ...
Troubleshoot error code “F13” in Fagor drying machine
How to eliminate F13 error in Fagor dryer? Error: F13Description: Problem in the flowmeter.Cause: Solution: - Check flowmeter, your connections and wiring. - Check the water pressure in the tap ...
Troubleshoot error code “F12” in Fagor drying machine
How to eliminate F12 error in Fagor dryer? Error: F12Description: Communication problem between electronic plates and components.Cause: Solution: - Check connections and washing wiring. - Check components and electronic plate ...