Boiler
Why your boiler will not start after summer and what to check
Check settings, pressure readings and lockout messages without opening the boiler or interfering with its internal systems.

A boiler that will not start when colder weather returns may have its heating function disabled, be receiving the wrong instruction from the thermostat or be locked out because of unsuitable pressure. An ignition or circulation fault is another possibility. The key is to check whether hot water works, what the display shows and what the pressure gauge reads, without opening the appliance or interfering with its systems.
If you have a problem with your boiler, you can use our free error code finder. It can help you identify errors and find straightforward, effective guidance on resolving them.
Hot water helps reveal where the problem begins
With a combi boiler, cold radiators do not necessarily mean the appliance has stopped firing. If water from the hot tap reaches its usual temperature, the boiler can still produce heat. Checks should then focus on the central heating demand, its settings and circulation to the radiators, although internal components may still be involved.
If there is no hot water either, the problem affects shared functions or startup more generally. A blank display points toward power or control issues; an illuminated display showing a warning indicates a lockout detected by the appliance. Neither situation identifies a failed component on its own. It is important to distinguish no response from ignition failure, because they are different symptoms.
Observe the boiler during normal use rather than triggering repeated starts. Notice whether a demand symbol appears, whether the appliance begins its usual sequence and whether it then stops. For a professional assessment, describing which service fails and when is more useful than assuming the entire boiler has failed because the house is not heating up.
This distinction also prevents summer from taking all the blame. Many boilers have continued providing hot water throughout those months: only the heating circuit has been inactive. Working showers do not prove that the thermostat, valves or circulation to the radiators have been tested. These are partly independent services, even though they share an appliance.
Summer mode and thermostat settings can leave heating on standby
Summer mode usually keeps domestic hot water available while disabling central heating. When temperatures fall, the boiler may simply continue following that setting without having developed a fault. Winter or heating mode should be selected using the normal user controls, as described in the model’s manual, without entering installer menus or changing technical parameters.
The thermostat may also be working correctly without requesting heat. This happens when its target temperature is below the room temperature, the schedule keeps heating off or an away period remains active. A room setting of 20 to 21°C is a comfort reference, but it will not necessarily create demand if the home is already that warm.
To check the response, the target temperature needs to be above the actual room temperature, and the schedule must allow heating at that time. There is no need to leave it excessively high: the aim is to see whether a heating demand appears, then restore the usual setting. On battery-powered thermostats, a dim or blank screen is a reason to check the batteries and their orientation in line with the instructions.
Wireless thermostats can lose communication with their receivers. Visible indicators and the manufacturer’s user procedure can help assess this. If checking requires access to wiring, removal of the receiver or work on connections, it belongs to a professional. Never join terminals to simulate demand: bridging thermostat connections is not a safe household test.
Check pressure when cold, but do not adjust it blindly
Reading the pressure gauge is one of the most useful checks when a boiler remains locked out. For many domestic installations, the usual cold reference is between 1 and 1.5 bar, although the manufacturer’s specified range for that appliance and installation takes priority. This general range should not be treated as a universal filling instruction.
Pressure below the minimum can prevent operation to protect the system. Below 1 bar, some boilers already display warnings or lock out, but the precise threshold depends on the model. Simply observe and record the reading when the system is cold; if the manual shows it is outside the permitted range, correction should be left to someone qualified to work on the circuit.
A high reading should not be dealt with by opening an arbitrary valve either. Water expands as it heats, so some variation between cold and hot is expected, but a sharp rise accompanied by discharge or dripping needs investigation. Among other items, a professional will need to assess the expansion vessel and pressure relief valve. The gauge provides a clue, not proof of which component has failed.
Pressure trends are more informative than a single number. If pressure drops again or changes substantially whenever the heating runs, there may be a leak or a problem accommodating expansion. You can look for accessible damp patches and drips without dismantling anything. Restoring pressure does not repair the underlying cause, and repeated corrections should not become routine.
When the boiler starts but the radiators stay cold
If the appliance responds to demand but the radiators do not warm up, the investigation changes direction. Heat may not be reaching them because of trapped air, closed valves or insufficient circulation. Cold patches or water noises in a radiator provide clues, but they do not prove that bleeding will solve everything. The important distinction is between failure to ignite and failure to distribute heat.
You can check the position of normal radiator valve controls and make sure they were not left at their lowest setting at the end of winter. This does not include removing valve heads, freeing pins with tools or adjusting lockshield valves to change the system’s balance. If a control resists movement, do not force it: a seized component needs assessment without causing a leak.
Bleeding releases air, but it can also alter pressure and involves opening a point in the heating circuit. It should therefore not be treated as an automatic test for every startup failure. If there are signs of trapped air, refer to the maintenance requirements for the installation and leave the work to someone who can perform it safely. Do not open bleed valves or drain points to clear a boiler lockout.
When no radiator receives heat despite a correct demand, the circulation pump, an internal valve or the appliance’s controls may be involved. If only one radiator is affected, the problem may be local to that radiator or its pipe branch. This distinction helps diagnosis but does not justify dismantling components. Checks on internal pumps and valves belong to a qualified heating engineer.
Error codes need a make, model and context
A code represents a condition detected by the electronics, not always the underlying cause. An ignition failure, for example, may involve supply, flame detection or control components. Before resetting, save a photograph of the warning and model details: the original message may disappear even though the problem still requires diagnosis.
The following examples relate to Baxi references and must not be transferred to other makes or every range from the same manufacturer. Displays can present messages differently, and their meaning must be checked against the specific manual. Also, a service message does not necessarily indicate a fault, as with certain indications associated with calibration functions.
| Code | Description | Cause | Safe response |
|---|---|---|---|
| E133 or 133, on applicable Baxi models | Lockout associated with unsuccessful ignition or failure to detect a flame. | Possible supply, ignition or detection issues; the specific cause requires diagnosis. | Record the code and consult the manual. If a user reset is permitted, follow only that procedure; stop trying if the fault returns. |
| E1 followed by 33, on certain Baxi displays | An alternating presentation of E133, not two separate faults. | The same ignition lockout condition described for E133 on the relevant model. | Record the full sequence so that only part of the warning is not reported. |
| E25 or 25, on Baxi models that define it this way | Warning associated with insufficient water circulation or an abnormal temperature rise. | Possible circulation, pump or hydraulic conditions within the system. | Observe the pressure without intervening. Pump and circuit checks belong to an engineer. |
| 303, in the calibration context of certain Baxi models | An indication described during a calibration function; not a universal ignition failure code. | In the referenced sequence, the calibration function has not been activated; this must be confirmed in the specific documentation. | Do not start or repeat calibration. Tell the engineer the model and the circumstances in which the message appeared. |
Buying an electrode, pump or control board based solely on this table would be premature. Symptoms overlap, and a code may describe the consequence of another problem. Before purchasing a spare part, there should be a diagnosis that justifies replacing it; otherwise, you may pay for an unnecessary component while leaving the original fault untouched.
A reset has limits and cannot replace diagnosis
A one-off lockout may allow a reset from the user panel, provided the manual permits it and there are no signs of danger. The button, how long it is pressed and the required conditions vary between models. There is no universal button sequence for every boiler. The safe approach is to follow the manufacturer’s specific procedure, not borrow instructions from a similar-looking appliance.
Before resetting, record the warning and check only accessible settings and readings. If the lockout returns after the permitted reset, do not keep trying until the burner eventually lights. Running for a while does not prove the cause has been resolved. A recurring lockout requires investigation, especially if ignition cuts out or unfamiliar noises appear.
Calibration functions, combustion adjustments and installer-only menus are not alternative household reset methods. They can change essential operating conditions and require knowledge and instruments. Sensors and protective devices must not be bypassed to complete a test either. Users should not change service parameters, even if they find a button sequence published online.
Gas, flue systems and electricity define the safety boundary
If the display stays blank, you can look at the normal operating switch and check whether the home has a general power outage. That check stops before removing a socket, opening the casing or accessing internal fuses and wiring. An unresponsive display does not prove the control board has failed; the cause must be established without improvised electrical work.
With a gas boiler, a supply interruption can also prevent ignition. You can check whether the gas network operator has reported an outage, but must not loosen connections, purge pipes or adjust regulators. Do not light another appliance to investigate if you smell gas. In that situation, do not operate switches or create flames; move away and contact the gas emergency service from a safe place.
Combustion gas discharge and, on condensing boilers, condensate drainage may also be involved in a lockout. You may only look for obvious damage from an accessible position, without dismantling ducts or reaching high-level terminals. Checks for obstructions, fan operation, sensors and combustion belong to a suitably qualified heating company, not an improvised cleaning attempt.
A carbon monoxide alarm, or symptoms such as headache and dizziness while the appliance is operating, require leaving the area and seeking urgent help from a safe location. Do not remain beside the boiler looking for the source. Carbon monoxide cannot be ruled out by the absence of a smell, and another ignition attempt is not a safety check.
A useful assessment starts before parts are replaced
For a professional visit, provide the make, model, full code, cold pressure reading and what happens with heating and hot water. Include whether the problem appeared when winter mode was selected or whether leaks, noises or temperature fluctuations were already present. This context helps guide testing without assuming a diagnosis before the appliance has been checked.
When a repair is proposed, the price should relate to a diagnosis and clearly defined work. Before agreeing, establish whether travel and diagnosis are charged separately, what labour includes and whether those charges are deducted if the repair goes ahead. There is no universal price covering every model, location and fault, so a figure without those conditions may be misleading.
The choice between repair and replacement does not depend on age alone either. Overall condition, spare-part availability, fault history and total cost compared with a newly installed appliance all matter. A settings issue does not justify replacing a boiler; a major repair calls for a broader assessment. If cover is still in place, check its terms before authorising work or buying parts.
The first startup should restore stable operation
Starting the boiler after summer is not complete simply because a flame appears. Expected behaviour is for the appliance to meet demand, distribute heat and stop according to its controls, without repeated lockouts or leaks. Very frequent starts, new noises or persistent differences between radiators deserve attention. Starting and operating correctly are different things.
Checking ahead of the point when continuous heating is needed gives time to identify problems without relying on the first cold day. Maintenance should follow the manual and the requirements applicable to the installation; a commercial recommendation for annual servicing should not be confused with a universal legal interval. The priority is to maintain the appliance according to its actual requirements and not postpone investigation of recurring symptoms.
If the controls are correctly set, the pressure reading has been checked against the manual and the problem continues, the next step is diagnosis by a qualified professional. Up to that point, observation provides information; beyond it, interference adds risk without guaranteeing a solution. A successful return to operation should mean stable heating and intact safety protections, not a boiler kept running through repeated resets.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoSaeco coffee machine error 1: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Coffee machine7 days agoJura coffee machine error 8: what to do and repair costs
Coffee machine7 days agoJura coffee machine error 5: what it means and what to do
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions





















