Beko
Error E06/E07 in Beko dishwasher

Error E06/E07 in Beko dishwasher
The error code E06/E07 in Beko dishwashers indicates an anomaly in the temperature reading system. Specifically, it refers to a problem with the dishwasher’s thermal probe (NTC sensor), which measures water temperature during the washing cycle. When the electronic control unit detects a short circuit or an out-of-range reading from this sensor, it interrupts the program to prevent damage or faulty operation.
What does the E06/E07 error mean?
This error occurs because the dishwasher’s electronics rely on accurate temperature data to manage the wash cycle correctly. The temperature probe changes its resistance based on the water temperature, and the control board interprets this signal to regulate heating and cycle timing.
If the control board receives a distorted or incompatible signal, it assumes a fault in the thermal probe circuit and stops the cycle as a safety measure. This prevents overheating, incomplete washing, or damage to the heating element and other components.
Difference between E06 and E07
- E06: Dishwasher thermometry fault caused by a shorted or out-of-range temperature probe reading.
- E07: Equivalent fault in the probe circuit, including wiring or connectors.
- E06/E07: General thermal reading lockout due to incompatible signal.
Both codes point to the same core issue related to the thermal sensor and its circuit, with the number varying depending on the dishwasher model or family.
How does the error present in everyday use?
The first sign of this issue is usually a sudden interruption of the cycle. The dishwasher might start normally but then stop mid-cycle, leaving water inside or failing to complete the wash. In some cases, the error code appears immediately and prevents the cycle from starting.
Additional symptoms can include:
- Dishes coming out lukewarm or poorly washed, especially in programs that require heating.
- Tablets not dissolving completely.
- Unexpected pauses or stalls during the cycle.
It is important not to confuse this error with drainage or water supply issues. The presence of the E06/E07 code specifically points to a thermal measurement problem rather than mechanical faults.
Main causes of the E06/E07 error
- Damaged NTC sensor: The temperature probe is a small, inexpensive component exposed to heat, moisture, and detergents. Over time, it can fail or provide erratic readings.
- Faulty wiring or connectors: Wiring sections passing through the door and base endure constant movement, which can cause broken conductors, insulation wear, or corrosion.
- Control board failure: Although less common, the control board itself can malfunction and misinterpret signals, especially if the sensor and wiring have been checked and replaced.
What can you do to solve the error?
Basic troubleshooting at home
- Turn off the dishwasher and unplug it for a few minutes. This can clear temporary electronic glitches.
- Restart the appliance and observe if the error reappears. If it disappears, the fault might have been a one-off issue such as a power surge.
- Perform a visual inspection of the sensor wiring and connectors. Look for moisture, corrosion, loose connections, or damaged cables, especially in areas that experience frequent bending.
When to seek professional help
If the error persists after restarting and basic checks, the fault is likely stable and requires a technical diagnosis. Replacing the NTC sensor is often the most straightforward repair, but it is important to verify the wiring and control board condition first to avoid unnecessary replacements.
Professional technicians can accurately diagnose the problem and ensure the correct component is repaired or replaced, preventing recurring errors or further damage.
Summary of solutions
| Code | Description | Cause | Indicative solution | Severity |
|---|---|---|---|---|
| E06 | Dishwasher thermometry | Temperature probe shorted or out-of-range reading | Turn off, wait a few minutes, and restart; if it returns, inspect sensor and wiring | Medium |
| E07 | Dishwasher thermometry | Equivalent fault in the probe circuit | Check NTC sensor, connectors, and control board | Medium |
| E06/E07 | Thermal reading lockout | Signal incompatible with temperature measurement | Technical diagnosis if warning repeats after restart | Medium |
Additional recommendations
If you have trouble solving the error yourself, we recommend contacting Beko technical service or an appliance specialist. They can diagnose the issue precisely and carry out the necessary repairs.
For more information on Beko dishwasher error codes, you can consult our error code finder to identify and resolve other faults easily and effectively.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions
Air fryer6 days agoE3 error on a Cecotec air fryer: what to do and what to avoid





















