Drying machine
E43 Error on Electrolux Dryer: Causes and Useful Checks
The E43 warning points to the door closure. Check the door lock, wiring and control board before it develops into a more serious fault.

The E43 error on an Electrolux dryer almost always points to the door locking system and, in particular, to the door lock or the signal confirming that the lock has engaged. The machine protects itself and will not start the cycle when that check fails, even if the door appears to be properly closed from the outside.
In practice, the warning may be caused by a worn latch, poor front-panel alignment, a loose wire, or the electronic stage that controls the lock. The correct diagnosis does not start with the drum or the drying process, but with start-up safety: if the dryer does not receive confirmation that the door is closed, it stops before starting.
If you have a problem with your dryer, you can use our free error code finder. From there, you can find out what all the errors mean and solve them easily and effectively.
What the E43 warning really means
E43 does not describe a drying fault, but rather a problem in the circuit that authorizes the program to start. Electrolux uses this control as a safety barrier: the dryer needs to know that the door is firmly closed and that the internal lock has responded properly. If that confirmation does not arrive, the appliance stops the process or prevents the cycle from starting.
That behavior makes technical sense. A drum rotating with the door improperly confirmed is not just an inconvenience; it is a mechanical and electrical risk. That is why the system reacts firmly to a weak, intermittent, or missing signal. The panel may turn on, the controls may respond, and yet the machine may remain still because of a tiny detail somewhere in the locking chain.
The most useful symptom when interpreting the code is the sequence: the door closes, the user presses start and, almost immediately, the warning appears or the cycle fails to begin. When the pattern repeats this way, the suspicion shifts away from incorrect use and focuses on the door lock, its connections, or the control board.
The locking chain that usually fails
An Electrolux dryer door does not work like a simple cover. Behind the action of pushing it shut and hearing the click, there is a safety component, a mechanical housing, and a small circuit that reports back to the electronics. When one of these elements fails, the whole system loses consistency and the machine interprets the door as not ready for operation.
The door lock is the first suspect because it ages with use, takes the impact of repeated closing, and may lose firmness in its internal contact. Sometimes the door appears to close normally, but the switch does not transmit the correct signal. At other times, the lock does engage, but late or irregularly, which is enough for the system to protect itself and trigger E43.
The alignment of the front panel may also play a role. A sagging hinge, a misaligned hook, or a displaced seal can change the geometry of the lock by a few millimeters. It may not seem like much, but in this type of appliance, a very small adjustment can make the difference between a stable reading and an intermittent fault that comes and goes.
Table of errors related to the door lock
Within the group of faults related to the door, code E43 has a clear place, but it does not work alone. Electrolux and similar brands use a comparable logic in this safety section, and it is worth distinguishing the warnings so that a mechanical problem is not confused with an electronic one.
| Code | Description | Cause | What is usually checked | Severity |
|---|---|---|---|---|
| E43 | Fault related to the door lock | The door does not confirm closure or the signal does not reach the control board | Latch, door lock, wiring, and electronic response | Medium to high |
| E48 | Door locking or door confirmation problem | The lock is not validated | Door fit, contacts, and circuit continuity | Medium to high |
| E45 | Fault in the electronic control of the lock | The board does not properly control the locking command | Triac, connections, and main module | High |
What to check before assuming a major fault
The first useful check is always visual and tactile. With the dryer unplugged, it is worth opening and closing the door several times, slowly, while looking for a firm, consistent click. If the lock bounces back, feels loose, or requires excessive pressure, the clue lies in the mechanics. In many cases, the problem can be detected without taking anything apart, simply by paying attention to how the door fits.
The front-panel edge also matters. Compacted lint, dirt, or a slight deformation in the frame can prevent the latch from seating properly. A dryer door may seem like a minor component, but it works like a precision lock: a small misalignment alters the system’s entire reading and leaves the appliance in standby.
If the fit seems correct, the next logical step is to look at the door lock and the area immediately around it. A slightly loose connector, a fatigued terminal, or a wire strained by vibration can cause an intermittent signal. With faults of this kind, the problem is often not with the outside of the door, but with the internal communication between the door and the control board.
When the door lock stops responding
The door lock acts as the gatekeeper for start-up. Its job is twofold: to confirm that the door is closed and to provide a clear signal to the electronics so that the cycle can begin. When this component wears out, the internal contact is no longer as precise and the dryer interprets the door as still open, even when it does not appear to be.
A typical symptom is inconsistency: the door closes seemingly normally, but the machine does not respond or stops the start-up process immediately. This behavior points to a fatigued internal contact, a mechanism with too much play, or minor damage preventing the lock from being confirmed securely.
Over time, repeated use can slightly deform the component or create play in the engagement area. In an appliance that is opened and closed every day, this kind of wear is not unusual. The most common repair in this situation is usually replacing the door lock, provided the rest of the circuit shows no additional damage.
The electronic board may also be behind it
When the door appears to be fine and the fault persists, attention shifts to the control board. It is not always the culprit, but it comes into play because it is responsible for interpreting the locking signal and activating the lock. If that command is lost, the dryer remains stuck on the warning without completing the start-up process.
In some models, the problem is not a total board failure, but a specific control component, such as the stage that manages the locking command. A fatigued solder joint, a damaged trace, or a control element that no longer switches properly can produce a symptom very similar to that of a defective door. From the outside, the two faults look very much alike.
That is why a proper diagnosis is not based on guesswork. Measuring continuity and checking signals makes it possible to distinguish a simple worn component from a genuine electronic fault. Pressing the start button over and over will not fix anything; it only confirms that the control chain is still broken somewhere along the way.
Signs that help distinguish the cause
The exact moment when the warning appears provides quite a lot of information. If E43 appears just after pressing start, the problem is usually in the lock or the door lock mechanism. If it appears intermittently, after several attempts, suspicion broadens to the wiring or the control board. The frequency of the fault says more than the code alone.
The appliance’s recent history can also help. A dryer that has been moved, transported, or hit around the front may have developed a door misalignment without there being any serious fault. By contrast, a machine that has always closed properly and suddenly starts failing usually points to internal wear or a contact that is no longer working consistently.
Even the way the door feels when closing matters. If it used to slide in smoothly and now offers unusual resistance, if the lock sounds hollow, or if the latch seems to drag, your hand is already warning you about what the display will later confirm. In these cases, the panel is not inventing the problem; it is simply translating a mechanism that has lost precision.
Reset, checking, and reasonable limits
A basic reset may clear a temporary lockout, but it will not solve a physical cause. Unplugging the dryer for a few minutes and trying again can help if the board has become stuck on an incorrect reading, although E43 returning afterward points to a persistent fault. The important thing is not to mistake temporary relief for a solution.
Forcing the door will not help either. If the latch does not seat properly, applying more pressure can damage the frame, deform the lock, or finish breaking an already fatigued door lock. The line between a household check and a technical repair is clear here: checking the fit, cleaning the surrounding area, and observing the response are reasonable; dismantling or measuring components requires tools and experience.
When the fault repeats even though the door closes properly, the correct route is a technical one. On an appliance that has been used for several years, the door lock is usually more likely to be at fault than the control board, but not always. The context, the panel’s behavior, and the response of the lock help shape the diagnosis far more reliably than simply hoping the error will disappear on its own.
What this fault reveals about dryer maintenance
E43 teaches a simple lesson: a clean, properly aligned door prevents many false alarms. Lint, dirt on the front panel, and slamming the door may not seem like serious issues, but they eventually punish the small components that support the safety of the entire machine. Wear does not always arrive as a major breakdown; very often, it builds up little by little, almost silently.
It also reminds us that modern electronics depend on very specific signals. A contact, a triac, or a small switch does more work than can be seen from the outside. The dryer is not failing in the abstract; it is no longer receiving an essential confirmation and stops so it does not continue under uncertain conditions.
Seen this way, this code is not a dramatic message, but a precise indication. The machine is saying that the door system does not seem reliable. Once that logic is understood, diagnosis stops seeming mysterious and becomes an orderly sequence of checking the mechanics, wiring, and electronic controls.
A small warning that protects an entire machine
The value of this fault lies in what it prevents. The dryer blocks start-up to prevent unsafe operation, protect the electronics, and preserve the mechanical assembly. It can be frustrating to find the laundry waiting behind a door that seems closed while the panel does not progress, but this early interruption is usually preferable to starting the machine with its safety compromised.
On an Electrolux dryer, E43 almost always brings the discussion back to the same points: door, door lock, wiring, and associated control board. Checking this sequence calmly reduces unnecessary part replacements and prevents a simple misalignment from being confused with a more expensive electronic fault. The code does not call for drama; it calls for method.
Once the locking system is working precisely again, the machine returns to its normal rhythm and the warning disappears. What seemed like a complex fault is often, in reality, a very specific interruption in a short but decisive chain. And that, precisely, is the usefulness of the code: clearly pointing to where to look first.
More error codes: Electrolux dryer error codes: a clear and useful guide.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine7 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine7 days agoXiaomi launches steam air fryer in Spain for €179.99
Magazine7 days agoMan affected by smoke in Valladolid fire
Air fryer7 days agoCecotec air fryer E1 error: what to do safely
Heat pump6 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine6 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Air fryer6 days agoE3 error on a Cecotec air fryer: what to do and what to avoid
Magazine5 days agoENISA warns home appliances could be the next cyberattack target





















