Samsung
5C error on Samsung washing machine: causes, inspection, and solution
A draining failure in Samsung usually points to the filter, the pump, or the drain hose.

Imagen: bigsurprisetoys2016 / Pixabay
5C error on Samsung washing machine: causes, inspection, and solution
The drain warning on a Samsung washing machine appears when the appliance cannot empty the drum within the time expected by its electronic control system. In practice, the machine stops the cycle for safety because the water is not leaving at the speed the electronics consider normal. The most useful interpretation is simple: the washer has detected a problem somewhere along the route through which the water should leave.
When this happens, the cycle may stop before spinning, remain paused with water inside the drum, or make a brief humming sound while the drain pump attempts to work. The warning is designed to prevent overflows, bad odors, damage to the pump, and the mechanical stress that could occur if the drum tried to spin while it was still too full of water.
This does not necessarily mean that the washing machine has suffered a serious breakdown. In many cases, the solution is limited to cleaning the filter, checking the drain hose, or removing a coin, bobby pin, clip, piece of plastic, or buildup of lint that is blocking the pump impeller. Only when those basic points have been ruled out does it make sense to suspect a worn pump, a partially blocked household drain, an electrical fault, or a sensor that is not correctly confirming that the water has been removed.
If you have a problem with your washing machine, you can use our free error code finder. From there you can identify and solve all errors easily and effectively.
What the 5C drain warning really indicates
The washing machine does not simply switch the pump on and wait. Samsung washers monitor the water level and the time required for drainage in real time. When the wash ends, and again when the appliance is preparing to spin, the control system expects the level inside the tub to fall within a specific margin. If the level does not drop quickly enough, the electronics interpret the situation as a drainage failure and display the corresponding code.
The signal appears especially often at the end of the cycle or just before spinning. At that moment, the washing machine needs the tub to be sufficiently empty so that the drum can rotate stably. If too much water remains, the machine stops the sequence instead of continuing as if everything were normal.
This forced pause is not arbitrary. It protects the motor, belt, bearings, pump, and electronic components. It also reduces the risk of an overflow and prevents the drum from spinning with excessive weight and resistance. In other words, the code responds to a measurable condition: the water is leaving more slowly than expected or is not leaving at all.
The most recognizable symptoms include:
- Water remaining inside the drum at the end of the wash.
- A cycle that stalls immediately before spinning.
- A short, dry, weak, or irregular humming sound from the drain pump.
- A gurgling sound in the drain circuit.
- A longer-than-usual pause at the end of the program.
- A small amount of water that remains after several cycles.
- The same drainage code returning after the washer attempts to empty itself.
The source of the failure is usually in the water path, not in the laundry and not in the control panel. That is why the diagnosis should begin at the bottom of the machine, with the filter and pump, and then continue through the hose and household drain. Technicians generally inspect the water flow and listen to the pump before considering a control board, wiring, or sensor problem.
5C, 5E, and SE: are they the same error?
On many Samsung washing machines, 5C and 5E refer to the same basic drainage problem. The exact code can vary according to the series, market, generation of the appliance, or panel nomenclature. SE is an older name or an equivalent designation on certain units. The difference is usually one of terminology, not severity.
| Code | Description | Common cause | Typical sign | Suggested solution | Frequency |
|---|---|---|---|---|---|
| 5C | Drain failure | Water is not evacuated within the expected time because of a clogged filter, bent hose, blocked pump, or another obstruction in the outlet circuit. | Water remains in the drum and the cycle stops, often before spinning. | Clean the filter, check the hose, inspect the pump, and then verify wiring or the level sensor if necessary. | High |
| 5E | Drain failure | The appliance reading changes depending on the series or market; the technical cause is usually the same as 5C. | The washer behaves in the same way: water remains inside and the program stops. | Apply the same diagnosis to the filter, pipe, pump, wiring, and drain system. | High |
| SE | Drain failure or equivalent older nomenclature | Less drainage than expected, an internal blockage, or an equivalent drainage fault on certain units. | The washing machine stops before spinning or remains with water in the drum. | Check for blockages and inspect the filter, hose, pump, and water-level detection system. | Medium |
When a newer Samsung model displays 5C instead of 5E, the technical response is normally identical. The machine cannot remove the water through the intended path. The order of inspection remains the same: filter, hose, pump, wiring, and sensor. The exact lettering should not distract from the hydraulic problem that the appliance is reporting.
The causes that most often block drainage
1. A saturated or clogged pump filter
The pump filter is the first suspect because it collects the material that leaves the clothes during washing. Lint, hair, detergent residue, paper, coins, buttons, clips, bobby pins, and other small objects can accumulate inside the filter compartment. In homes with pets, work clothes, very dirty garments, or frequent heavy loads, this buildup can appear sooner than expected.
Over time, these materials combine into a thick, sticky barrier. The water can still pass at first, but more slowly. The cycles become longer, the pump has to work harder, and eventually the control system no longer considers the drainage speed acceptable. The washing machine then displays 5C, 5E, or SE and stops.
A filter can look relatively clean from the outside while the real obstruction remains inside the filter housing. Compact lint, a hard piece of debris, or an object caught behind the filter may still restrict the flow. Thorough cleaning therefore includes both the part that unscrews and the opening or compartment where it fits.
2. A bent, crushed, or incorrectly installed drain hose
The rear drain hose can imitate a serious mechanical failure. If it is bent, crushed, twisted, pushed against the wall, inserted too deeply into the household drain, or installed too low, the water meets resistance as it tries to leave. The result can be slow drainage, backflow, unstable outlet behavior, or a siphoning effect.
Pushing the washer too far against the wall can pinch the hose as if an invisible hand had folded it in half. Even a small crush can be enough to slow the flow and make the code reappear. The hose should be secure and free from impossible bends, while still allowing the water to flow without sealing the outlet.
Installation height also matters. On many front-load Samsung washing machines, the usual drain outlet height is between 60 and 90 cm from the floor. On top-load models, the usual range is between 90 and 100 cm, depending on the model. The manufacturer’s installation instructions should take priority because the exact requirements can vary.
The end of the hose should not be pushed too far into the wall drain. In many installations, an insertion of approximately 15 to 20 cm is reasonable, with enough clearance for air and water to move without sealing the outlet. If it is inserted too deeply, the water may encounter unnecessary resistance or create a siphoning effect. If it is inserted too little, the hose may come loose during draining.
3. A blocked or weakened drain pump
The drain pump can be blocked without being permanently broken. A coin, hair clip, piece of plastic, or a fragment of stiff fabric can lodge in the impeller and prevent it from turning freely. In that case, the washer may produce a short hum but fail to move the water.
Other pumps are worn rather than blocked. Their motor loses strength, the rotor no longer turns with sufficient force, or the winding becomes unreliable. The pump may make an irregular or weak sound, start intermittently, or stop after a brief attempt. In some cases, it makes no sound at all, not even the initial start.
A pump that tries to work and only produces a dry hum usually gives an important clue. The impeller may be jammed, or the motor may no longer have enough power. If the filter is clean and the hose is correctly installed, the pump becomes the next logical link in the diagnosis.
4. A partially blocked household drain
The obstruction is not always inside the washing machine. A partially blocked siphon, wall pipe, standpipe, or household drain can restrict the water after it leaves the hose. The washer attempts to empty the tub, but the water meets resistance in the building’s plumbing. This can create a pattern that looks exactly like a pump failure.
A slow household drain may also produce gurgling, water backing up, or water returning toward the hose. For that reason, it is important to verify the complete outlet circuit instead of inspecting only the appliance.
5. A fault in the level or pressure sensor
The pressure or water-level sensor has a different role. The pump may drain the water correctly, but the sensor or its associated air path may fail to confirm that the level has fallen. In that situation, the drum is empty, yet the electronic control behaves as if water were still present.
This is not the most common cause, but it explains why some units continue to display a drainage warning even after the filter has been cleaned and the pump has done its work. It is a detection problem rather than a physical outlet problem.
6. Wiring, connectors, or a power-supply problem
The problem may also lie between the control system and the drain pump. A connector can become overheated, a wire can be damaged by vibration or moisture, or a poor contact can interrupt the pump’s operation even when the pump itself is in good condition.
Continuity, power supply, and connectors can be checked, but this is already technical territory. The appliance should be unplugged before any internal inspection, and users who are not trained to work with electrical components should stop at the basic filter, hose, and visible pump checks.
How to inspect the washing machine safely
Cleaning the filter requires order, not force. Before opening a lower panel or filter cover, disconnect the washing machine from the electrical supply. Prepare a towel, a low container, and some patience because residual water will usually come out of the drum or drainage compartment.
- Stop the program and unplug the washing machine.
- Place towels and a low container near the lower front area.
- Open the small lower access door, normally located near the floor on many front-load Samsung models.
- Look for the small emergency drain hose, if the model has one.
- Place the hose into the container and remove its cap slowly so the residual water can drain little by little.
- Once the emergency water has been removed, locate the main filter cap next to the emergency hose.
- Unscrew the filter carefully and allow any remaining water to escape into the container.
- Remove lint, hair, detergent residue, coins, buttons, clips, paper, and any other objects from the filter.
- Rinse the filter with water and inspect its threads and sealing area.
- Inspect the inside of the filter housing, not only the removable filter itself.
- Check whether the pump impeller is visible and whether it turns freely by hand without forcing it.
- Reinstall the filter securely, close the emergency hose, and close the access panel.
- Inspect the rear drain hose and the household drain before reconnecting the washer.
- Run an appropriate drain or rinse test and observe whether the water leaves normally.
The exact arrangement varies by model. Some Samsung machines have an emergency drain tube, while others provide only the filter access. If there is no emergency hose, open the filter cap particularly slowly and keep the container and towels in position.
How to check the filter without making the blockage worse
Do not force the filter cap if it is difficult to turn. A hard cap may be affected by debris, pressure from retained water, or residue in the threads. Applying excessive force can damage the cap or its seal. Work gradually and keep the appliance disconnected from power throughout the basic inspection.
When the filter has been removed, clean both sides and examine the central opening. Residue may be compacted inside the housing even when the filter itself appears clean. A coin or hard plastic fragment can also remain behind the filter and interfere with the impeller.
By hand, and always without forcing it, check the pump impeller. It should not be completely locked. Some pumps turn with a slight stepped resistance because of the motor’s magnetic design, but a rotor that feels stiff, stops abruptly, or moves in jerks can indicate an obstruction or a damaged pump.
Do not repeatedly run full cycles in the hope that the pump will clear itself. If an object is lodged in the impeller, repeated attempts can place unnecessary strain on the motor and accelerate wear.
How to inspect the drain hose and its installation geometry
After the filter has been cleaned, examine the entire visible length of the drain hose. It should not be crushed behind the washing machine, folded sharply, twisted, or trapped between the appliance and the wall. Move the washer carefully if necessary, without pulling abruptly on the hose or electrical cable.
Check that the hose is installed at the correct height above the floor. On front-load models, the usual range is between 60 and 90 cm; on top-load models, it is normally between 90 and 100 cm, depending on the model. A hose that is too low can encourage unstable drainage or siphoning, while a hose that is too high can make the pump work against unnecessary resistance.
Inspect where the hose enters the household drain. It should generally be inserted around 15 to 20 cm, although the model’s installation instructions remain the final reference. An end inserted too deeply may restrict air movement or encourage siphoning. An end inserted too little may detach and release water onto the floor.
The outlet must not be sealed airtight. Water needs a clear path to flow, and the drain must be able to accept the volume discharged by the washing machine. If the wall pipe is slow, blocked, or gurgling, the problem may be in the household plumbing rather than in the Samsung appliance.
What the pump sounds can tell you
The drain pump often provides a useful acoustic clue. It has its own language, although the sound alone cannot replace a complete inspection.
- A brief hum with no water movement: the impeller may be blocked by a coin, clip, plastic fragment, or another small object.
- A weak or irregular hum: the motor may have lost strength, or the pump may be struggling against a partial obstruction.
- A repeated start-and-stop sound: the pump may be worn or its electrical supply may be intermittent.
- No pump sound at all: the pump may have failed, or the wiring, connector, control output, or power supply may be defective.
- A louder grinding or rattling sound: the impeller or pump assembly may be damaged, even if some water still leaves the drum.
Some blockages are so small that they are difficult to notice at first glance. A coin, a hair clip, or a piece of stiff fabric may stop the impeller without producing an obvious visual sign. This is why the pump should be considered after cleaning the filter and checking the hose, but before replacing unrelated parts.
What to do when the pump still will not move the water
If the filter is clean, the filter housing is clear, the impeller is not blocked, the hose is correctly positioned, and the household drain is open, suspicion shifts toward the pump itself. The washing machine may still try to run it with a faint murmur before giving up, or it may remain completely silent.
A pump that has lost motor strength may not be able to move water even though it appears to start. In other cases, the motor winding is damaged, the rotor is worn, or the complete assembly has become unreliable. A replacement pump is often a manageable repair on a relatively recent washing machine.
When the pump truly fails, the repair is no longer a simple household task. A technician may need to check:
- Continuity through the pump.
- The electrical power supplied to the pump during the drain command.
- The pump connector and terminal condition.
- Wiring continuity between the control system and the pump.
- Signs of overheating, moisture, corrosion, or vibration damage.
- Whether the pump assembly itself needs replacement.
It is possible for the pump to be in good condition while a damaged connector or broken wire prevents it from working. Vibration, moisture, and the passage of time can leave marks on the circuit. An overheated connector may interrupt the pump even when the mechanical component is fine.
Do not force the pump or insist with repeated cycles. Repeated attempts can accelerate wear and place additional stress on a component that is already struggling. If the appliance still displays 5C, 5E, or SE after the basic checks, technical service is the safer next step.
How to distinguish a simple blockage from a larger fault
When the cause is simple dirt, the washing machine usually gives gradual warnings. Drainage becomes slower than before, a small gurgle appears, the program pauses for longer at the end, or a small amount of water remains in the drum. The problem often grows over time like a crust rather than appearing without any prior sign.
A more serious failure tends to change the behavior of the appliance. The pump may emit no sound, the error may return immediately after the drain attempt, or the washer may continue to stop even after the filter and hose have been correctly checked.
| Observed behavior | More likely explanation | First action |
|---|---|---|
| Water drains slowly and the filter contains lint or small objects. | Accumulated dirt restricting the outlet. | Clean the filter and its housing thoroughly. |
| The pump hums but the water does not move. | Blocked impeller or weakened pump. | Disconnect power, inspect the impeller, and do not force it. |
| The hose is crushed or installed too low or too deeply. | Incorrect installation, resistance, or siphoning. | Correct the hose position and verify the household drain. |
| The pump is silent during a drain command. | Pump failure, wiring problem, connector fault, or control issue. | Stop basic troubleshooting and arrange a technical inspection. |
| The drum empties but the code remains. | Water-level or pressure-sensor detection problem. | Have the sensor, air path, wiring, and control system checked. |
| The code returns together with leaks, bearing noise, knocks, or severe vibration. | Drainage fault combined with broader appliance wear. | Evaluate the overall condition before authorizing a repair. |
There is also a middle scenario in which the washer manages to drain but the electronic control still believes that water is inside. The water leaves, but the electronics do not realize it. That pattern generally points to a detection problem rather than an obstruction in the outlet path.
The role of detergent, the door gasket, and the detergent drawer
Accumulated dirt on the door gasket, detergent drawer, and pump filter can contribute to this type of issue. Large doses of detergent or unsuitable products create excess foam and leave residues that travel through the internal circuit. The residue can mix with lint and hair, forming a sticky film that restricts drainage.
More detergent does not mean better washing. Excess foam can make it harder for the appliance to interpret the water level, lengthen the cycle, and dirty the pipes and pump area. This does not mean that excess foam is the only possible cause of a 5C warning, but it is a recurring contributing factor in heavily used appliances.
Use detergent intended for automatic washing machines and follow the recommended dose. A correct quantity reduces residue and helps keep the hydraulic circuit cleaner. Front-loading machines often show the effects of excess foam quickly because their drainage and water-level margins are narrower.
Why preventive maintenance matters
Drainage failures commonly develop gradually. A garment with coins in its pocket, a button, a hair clip, paper, too much detergent, pet hair, or dirt carried by heavy fabrics can travel toward the filter and pump. At first, the appliance may only take longer to empty. Later, the obstruction becomes complete enough to trigger the code.
Regular maintenance reduces much of this risk:
- Check and clean the pump filter every few weeks under normal use.
- Inspect the filter more carefully in homes with pets, work clothes, very dirty garments, heavy fabrics, or frequent washing.
- Check pockets before washing, especially in children’s clothing, jeans, workwear, and garments with rivets or loose items.
- Clean the detergent drawer and door gasket.
- Use detergent for automatic machines and avoid excessive quantities.
- Inspect the rear hose regularly for crushing, twisting, or incorrect positioning.
- Pay attention to new humming, gurgling, slower drainage, or longer pauses.
The washing machine often warns the user softly before it stops completely. It does not usually break all at once. A cycle that takes longer, a slight buildup of water, or a strange sound can be an early signal that the drain path needs attention.
It also helps to listen to the appliance. Samsung electronics protect the machine rigorously and may stop before the damage becomes worse. Understood correctly, that caution is not bad news: it is the last barrier before retained water develops into an overflow, pump failure, or broader mechanical problem.
When it is worth repairing the washing machine
There is a clear distinction between a blockage and a mechanical or electrical failure. If water is not leaving because of dirt in the filter, the repair is cheap and quick. If the hose is incorrectly installed, correcting its position is also normally straightforward. A worn or blocked pump is more involved, but replacing it often still makes economic sense on a relatively recent washing machine.
The decision changes when the appliance has several other symptoms, such as:
- Loud bearing noise.
- Leaks.
- Knocks during spinning.
- Severe or increasing vibration.
- Intermittent electronic faults.
- A control board with several unrelated symptoms.
- Repeated pump, sensor, and wiring problems.
In an older machine, the 5C warning may be only the first visible part of a broader problem. Small weaknesses can accumulate, and the drainage system may be the first component to appear on the display. The age of the appliance, its overall condition, and the price of the replacement part should determine the decision.
A clogged filter, residue in the pump housing, or a hose installed incorrectly almost always justifies intervention. A worn pump usually does as well. When the drainage warning appears together with electrical faults, leaks, bearing noise, or other expensive failures, the balance may shift toward a broader repair or replacement.
Safety warnings before inspecting the drain system
- Always unplug the washing machine before opening the filter compartment or touching the pump area.
- Assume that residual water will come out, even if the machine appears nearly empty.
- Use towels and a low container to prevent water from reaching the floor or electrical connections.
- Open the emergency hose or filter cap slowly.
- Do not force the impeller or insert tools into it aggressively.
- Do not inspect internal electrical parts while the appliance is connected to power.
- Do not repeatedly run cycles when the pump is humming without draining.
- If the pump, wiring, connector, sensor, or control board must be tested, use a qualified technician.
A complete diagnostic order for the 5C error
The most efficient diagnosis follows the route of the water instead of replacing parts by intuition. Start with what is visible and easy to verify, then move toward internal components only if the warning persists.
- Confirm that water remains in the drum or that the cycle stops during draining.
- Disconnect the washing machine from power.
- Drain residual water through the emergency hose if available, or open the filter carefully with towels and a container ready.
- Remove and clean the pump filter.
- Clean the filter housing and inspect for hidden lint, coins, plastic, or other debris.
- Check whether the pump impeller turns without being forced and without feeling stiff or jammed.
- Inspect the rear hose for crushing, twisting, sharp bends, or damage.
- Verify the hose height: commonly 60–90 cm for front-load models and 90–100 cm for top-load models, depending on the model.
- Verify that the hose enters the household drain by approximately 15–20 cm without sealing the outlet.
- Check whether the household drain or siphon is partially blocked.
- Run a suitable drain test.
- Listen to the pump and observe whether the water moves.
- If the fault remains, have the pump, power supply, wiring, connectors, pressure sensor, and control system checked.
This sequence prevents a simple blockage from being mistaken for an electronic failure. It also avoids changing the pump when the real problem is a crushed hose or a household drain that cannot accept the discharged water.
A common fault that almost always starts at the bottom
The message on the screen may seem mysterious, but the source is usually close to the floor. The drainage circuit is a simple chain: water leaves the tub, passes through the filter, reaches the pump, travels through the drain hose, and finally enters the household drain. If one of those links becomes blocked or restricted, the entire washing machine stops.
Behind the code there is usually a blockage, not a mystery. That is the value of a methodical inspection: it separates a simple and inexpensive obstruction from a worn pump, faulty wiring, or a sensor problem before parts are replaced by guesswork.
When electronics intervene, the displayed code acts as a translator. It does not always identify the exact component at fault; it reports the symptom that the washing machine can measure. For that reason, the correct diagnosis starts with the water, continues with the filter and hose, examines the pump, and ends, if necessary, with wiring and the level sensor.
Time works in favor of the user who acts quickly. The sooner the filter is cleaned, the hose checked, and a blocked pump ruled out, the less wear there will be on the rest of the appliance. The washing machine does not ask for much: water must enter, circulate, and leave through the intended path.
What to remember when the drum does not empty
The 5C, 5E, or SE warning is usually not a technical mystery but an interruption of flow. The water has become trapped somewhere along its route, and the washer has stopped to protect itself. That protection may be inconvenient, but it prevents more expensive damage and indicates where to look first.
In most homes, the solution begins with a clean, methodical inspection of the filter, hose, and pump. Only when that path is clear and the warning persists does it make sense to consider the pressure sensor, wiring, connector, or control system. The order should not be skipped because, in a drainage problem, order is almost everything.
A small clog can immobilize an entire washing machine. Conversely, careful cleaning can restore the cycle in a few minutes. That contrast explains why this warning is one of the most frequent Samsung washer faults and why it is also commonly resolved by inspecting the less visible parts of the appliance.
The practical summary is straightforward: check the water, unplug the machine, drain the residual water safely, clean the filter and its housing, inspect the impeller, verify the hose geometry and household drain, and then evaluate the pump or sensor only if the problem remains. The most useful thing is not to memorize the code, but to understand the system behind it.
| Code | Description | Cause | Solution | Frequency |
|---|---|---|---|---|
| 5C | The washer does not drain water properly. | Clog in the filter, drain hose, pump, household drain, or a related detection problem. | Clean the filter and housing, check the hose and drain, inspect the pump, and test the sensor or wiring if required. | High |
| 5E | Equivalent drainage fault in some Samsung models. | The panel reading changes depending on the series or market; the technical cause is usually the same as 5C. | Apply the same diagnosis to the outlet circuit: filter, hose, pump, wiring, and sensor. | High |
| SE | Equivalent or older name for the same problem on certain units. | Less drainage than expected or an internal blockage in the water outlet circuit. | Inspect the filter, hose, pump, household drain, and water-level detection system. | Medium |
In newer Samsung models, the difference between 5C and 5E is generally a matter of nomenclature rather than severity. The bottom line is the same: the washing machine cannot remove the water within the expected time. The technical response is therefore almost identical, with small variations depending on the generation of the appliance and the panel installed.
When the drum stays full, think first about the bottom of the appliance, not the top. A clean filter, a correctly positioned hose, and a freely moving pump resolve a large proportion of cases. If those elements are clear and the error continues, the next step is a technical inspection of the pump, wiring, connectors, and level sensor.
More error codes: Samsung washing machine errors and error codes: a useful guide.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions
Air fryer6 days agoE3 error on a Cecotec air fryer: what to do and what to avoid





















