Washing machine
E24 Error in Zanussi Washing Machine: Causes, Diagnosis and Solution
The warning points to a drainage fault. Here’s how to identify it, diagnose it and fix it without blindly guessing.

The E24 warning on a Zanussi washing machine appears when the water is not draining as quickly as expected and the appliance interrupts the cycle for safety. In practice, the machine is left with water inside, the pump may hum without emptying it and the laundry ends up excessively wet, as if the programme had got stuck in the final stage.
The most common cause lies in the drainage circuit: blocked filter, crushed hose, worn pump or a blockage at the outlet point. To a lesser extent, the cause may be in the wiring or in the electronics that control draining, but the problem almost always starts with something as simple as a coin, compacted lint or an excessive bend in the pipe.
If you have a problem with your washing machine, you can use our free error code finder. From there, you will be able to find out about and solve all errors easily and effectively.
What the E24 warning really means
E24 is a drainage fault. It does not refer to the programme stopping for no reason or to a washing problem, but to the inability to remove the water accumulated in the drum within the time allowed by the system. The control board monitors this time and, if draining takes too long, stops the sequence to prevent overloads, overflows or spinning with the drum half full.
This detail completely changes the approach to the diagnosis. When E24 appears, suspicion is directed towards the final stage of the cycle, precisely where the washing machine expels the water into the household drain. If the appliance washes normally but becomes stuck while rinsing or spinning, the problem is usually in the outlet path, not in the water supply or the main motor.
The symptoms are usually quite recognisable: water retained in the drum, a deep hum during draining, repeated pauses and, sometimes, an attempt to pump that lasts a few seconds before stopping. The washing machine is not confused; it is warning that the water is not moving as it should and that continuing to force the cycle could make the fault worse.
The most likely causes behind the fault
The first part to suspect is the pump filter. Coins, buttons, threads, fabric residue and a layer of lint mixed with detergent accumulate there, eventually forming a thick paste. It is a small point, hidden behind a lower cover, but it works like an upside-down funnel: even a minor blockage is enough to slow the outgoing flow and trigger the error.
The second common cause is the drain hose. A fold caused by moving the washing machine, a tube positioned too high, a partially blocked wall outlet or an incorrectly fitted installation can produce the same symptom as an internal fault. Sometimes the water comes out in spurts and sometimes it does not come out at all, but the effect on the system is identical: the drainage does not meet the expected time.
The drain pump can also fail. It does not always break suddenly; quite often, it gradually loses power, the impeller becomes jammed by a foreign object or the motor sounds as if it were working with sand inside. In that situation, cleaning the filter is no longer enough. And if the pump is fine but is not receiving the correct command, attention turns to the control board or the wiring, although that hypothesis comes later in the diagnosis.
| Code | Description | Cause | Common symptoms | Severity |
|---|---|---|---|---|
| E24 | Water drainage fault | Blocked filter, blocked hose, damaged pump or defective pumping control | Water retained in the drum, humming while draining, cycle stopped | Medium |
The clues the washing machine leaves before you open anything
Before taking anything apart, the appliance’s own behaviour usually offers enough clues to avoid working blindly. If the programme stops just before the spin cycle, the system is pointing to draining as the problem area. If the washing machine tries to pump several times and then gives up, the problem may be intermittent, typical of a partial blockage or a pump that is beginning to lose performance under load.
The sound also matters. A constant hum without any real discharge usually points to a forced or blocked pump. An irregular noise, with pauses and restarts, suggests that the appliance is trying to drain, detects resistance and tries again. That sequence almost always points to a hydraulic fault rather than a washing fault. At that moment, the drum works like a cup that cannot quite empty through a narrow neck.
Visual inspection completes the picture. A hose bent behind the cabinet, a damp base or water on the floor changes the diagnosis and requires caution. Moisture and electricity should not coexist without checking the surroundings, so any test should begin by unplugging the appliance and cutting off the power if there are signs of a leak.
How to carry out an orderly and safe diagnosis
The first step is to cut off the power and, if necessary, close the water supply. This is not about being dramatic, but about preventing a simple fault from becoming a frightening electrical incident or causing more spillage than necessary. Afterwards, the filter deserves a careful inspection because it is the point where the material that eventually blocks the circuit accumulates. It is a good idea to place a container under the cover, as retained water may come out when it is opened.
When removing it, it is not enough to take out what is visible. You must check whether the pump impeller turns freely and whether there are hard fragments, pieces of fabric or foreign objects trapped in the housing. A coin may be enough to immobilise the system or reduce the flow to the point of activating the warning. In many household faults, the problem looks less like a breakage and more like a pipe trying to breathe through a straw.
The next check concerns the drain hose. It must be free of sharp bends, crushing or excessive height. It is also important to inspect the wall outlet or household trap, because a blockage in the home’s plumbing produces exactly the same effect as a slow pump. If everything external is correct and the error persists, then it makes sense to consider the pump, its connections or the control board.
Which repairs usually solve the problem
In a high proportion of cases, the solution is as simple as cleaning the filter and clearing the circuit. When the blockage is there, the washing machine immediately regains its drainage function and the cycle continues normally. It is an inexpensive repair, but it requires care so as not to overlook a small piece that could block the impeller again or damage the pump motor.
If the problem is in the hose, it is usually enough to reposition it, correct its height or replace it if it is deformed. This detail may seem minor, but a badly formed bend behind the cabinet can restrict the water flow just as effectively as a solid plug. In homes where the washing machine is frequently moved for cleaning or renovation, this deformation is one of the most repeated causes.
When the pump is worn, makes an unusual noise or fails to drain with the filter clean, the intervention becomes more technical. Replacing the drain pump is usually the decisive repair in those cases. And if the new replacement makes no difference, suspicion falls on the electronic board or the wiring, because the appliance may have the correct mechanical component but not receive the proper operating signal.
When it is no longer a household repair
There are signs that mean you must stop. If there are sparks, a burning smell, visible leaks near electrical components or strange noises that do not fit a simple blockage, the machine should not continue to be tested blindly. The combination of water and electricity turns a routine repair into an unnecessary risk, especially if the error occurs several times in a row.
It is also advisable to call a service technician when the warning returns after cleaning the filter, checking the hose and inspecting the home’s drain. At that point, the problem no longer looks like an isolated piece of debris, but rather genuine wear in the pump, an unstable connector or a control fault. If the appliance has been in use for years, the decision depends not only on the code, but also on the overall condition of the machine.
The logic is simple: if the drainage fails once because of dirt, it can be handled as a household repair; if it fails repeatedly, there is a component that is no longer responding as it used to. And that is when the error stops being a passing nuisance and becomes a sign of wear that should be read calmly, without forcing cycles or chaining restarts together.
Technical data that helps you choose the right replacement part
The drain pump in this type of washing machine usually operates at 230 V AC and a power rating close to 30 W, although the exact values depend on the model and series. In some replacement part references, winding resistance readings in approximate ranges of 5 to 15 ohms may appear, but this figure should not be taken as universal, because it varies according to the specific design.
In this area, the reference matters just as much as the part itself. The same assembly may vary in its mounting, connector or impeller geometry, and a pump that looks similar may not fit properly or may operate outside its specifications. Actual compatibility comes first, above visual similarity. That is why the full model number and rating plate remain the most reliable guide for avoiding a blind purchase.
It is also worth remembering that an incorrect replacement part can prolong the fault rather than solve it. If the part does not correspond exactly to the installed series, the fault becomes mixed up with the failed repair attempt and the diagnosis becomes more confusing. In household maintenance, precision is not a luxury: it is the difference between a fault being solved and an afternoon wasted.
Which models may show this warning
E24 has appeared on various Zanussi washing machines, including references such as ZWF 81240 W, ZWF 71240 W and ZWF 12381 W. This does not mean that the code is exclusive to those appliances; rather, it shows that it forms part of the diagnostic logic shared by several series in the Electrolux group, with design variations but a common approach to monitoring drainage.
Knowing the exact model is not a formality. It allows the parts diagram, pump, connector and outlet pump to be cross-referenced with much greater precision. In a brand with so many combinations of series, year and market, the model number is the key that separates a correct repair from an incompatible replacement part. The same fault does not always use the same part.
In addition, the way the error behaves is not always identical between appliances. Some washing machines stop abruptly; others try several times before giving up. This nuance does not change the basis of the diagnosis, but it does help reveal how the fault is progressing and whether the problem is gradually getting worse or appeared suddenly after a specific blockage.
What the drainage system reveals about actual wear
An E24 usually starts with something small, but it does not always end there. A clogged filter can be the first link in a longer chain: a forced pump, a damaged impeller, a loose connector and, finally, a control signal that no longer correctly interprets the draining command. From the outside it looks like a minor fault; inside, it is sometimes the sum of several signs of fatigue.
That is why it is so useful to read what the washing machine is telling you before clearing the warning and carrying on. If draining becomes slower, if the noise changes or if the laundry comes out increasingly wetter, the machine had already been giving warning signs. The code does not appear out of nowhere; it usually arrives when the system has already been working at its limit for a while and cannot remove the water in time.
In practical terms, dealing with the problem early is usually cheaper and less invasive than waiting for the pump to burn out or for the electronics to continue detecting a chain of faults. In a washing machine, the path of the water tells almost the whole story: from the drum to the filter, from the filter to the pump, from the pump to the hose and from there to the household drain. If one of those sections narrows, the machine stops breathing normally.
When draining stops being a detail and becomes the main clue
Modern washing machines depend on very precise mechanisms for something as ordinary as removing water from the drum. When E24 appears on a Zanussi, it is not the entire wash that is breaking down, but the end of the sequence, that stage where everything must flow as naturally as a properly installed pipe swallowing water without effort.
The fault, viewed calmly, usually follows an almost domestic logic: something blocks, something bends, something wears out. And when that point is corrected, everything else falls back into place. The drum empties, the hum disappears and the cycle continues. There is no sophisticated mystery, just a water route that needs to be clear so the machine can do exactly what it promises.
That is why the best approach is not to chase the code as if it were a riddle, but to methodically observe what is slowing down the drainage. Sometimes the answer is in a filter full of residue; other times, in a badly positioned hose; and in other cases, in a pump that no longer pushes with the same force. When the path is clear again, the washing machine regains its rhythm and the warning no longer has any reason to appear.
More error codes: Common Zanussi washer error codes and what they mean.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Magazine6 days agoMan affected by smoke in Valladolid fire
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine4 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















