AEG
E45 error in AEG washing machine: causes, symptoms and solution
The E45 code indicates a fault in the door lock and its associated circuit. Here’s how to identify and check it.

The E45 error on an AEG washing machine usually points to a fault in the door locking system, whether in the door interlock, the wiring that powers it or the electronics that control it. It is a typical safety warning: the machine detects that it cannot confirm the door is properly locked before starting the cycle and therefore protects itself by stopping or refusing to start.
In practice, the most visible symptom is clear: the door does not remain secured as it should, the programme is interrupted or the appliance stays idle for a few seconds before displaying the code. Sometimes the problem lies in a small component, invisible at a glance; other times, in the control board. The key is to determine whether the fault is mechanical, electrical or electronic, because the repair path changes considerably depending on its source.
If you are having a problem with your washing machine, you can use our free error code finder. From there, you will be able to identify and solve all errors easily and effectively.
What the E45 code on an AEG really means
AEG uses this warning to indicate that the door safety circuit is not closing the expected chain. Put simply, the machine is not receiving the confirmation it needs to start moving water, the drum and the motor normally. This confirmation does not depend only on the visible latch; the internal lock sensor, connectors, wiring harness and, on certain models, the electronic stage that interprets the signal are also involved.
That is why the E45 error should not be read as a simple case of the door not being closed properly. The door may be physically pushed shut and, even so, the appliance may remain locked if the locking system has lost continuity, if the triac on the board is not switching as it should or if the door lock has aged. In other words, the washing machine sees the lock, but does not consider it reliable.
This detail explains why many users go round in circles for hours: they press the door, restart the programme, unplug the appliance and try again. Sometimes it works temporarily, but the fault returns. When the code comes back quickly, the fault is no longer circumstantial; there is a part or connection that is failing repeatedly.
Symptoms that usually accompany the fault
The way the washing machine behaves is more helpful than it may seem. In many cases, the display shows E45 as soon as you try to start it. In others, the appliance starts emitting a repeated beep, blocks the start or runs for a few moments and then stops immediately. That brief pause is a useful clue: the machine tries to validate the lock, fails and cuts the sequence for safety reasons.
You may also notice that the door does not offer its usual resistance when closed, or that the lock makes a weak, intermittent click, as if it were stuck halfway. That short, dry sound, much like a tired switch, often gives away a worn mechanism. When the lock sounds unusual or operates with a delay, the door lock deserves immediate attention.
It is also worth checking whether the fault appears only when the door is heavily loaded with clothes or when the drum is pressing against the front panel. Sometimes the problem is not in the electronics but in the actual position of the door or in mechanical play that prevents the lock from working with the necessary precision. This difference is important, because a simple misalignment does not require the same intervention as a damaged board.
The most common causes behind E45
The first suspect is usually the door interlock. This is the part that secures the door before allowing the wash cycle to begin and, through wear or an internal fault, it may stop activating the correct signal. In a heavily used washing machine, this component withstands heat, pressure and constant vibrations; it is not unusual for it to lose reliability over time.
Another common cause is the wiring. A loose connector, a broken wire or a damaged track between the door and the board can interrupt communication even when the mechanism appears intact. In real-world repairs of this kind, the problem is not always visible from the front; many times it is behind the front panel, at a point where repeated movement eventually takes its toll. An intermittent connection can cause a more unpredictable error than a broken part.
The electronics also come into play. On some AEG models, the warning may be related to the door-lock triac input on the control module. This means that the board is not managing the locking command correctly or is not interpreting the response as valid. When the fault is in this area, forcing restarts will not solve anything: the system will continue detecting an underlying anomaly.
Finally, the door itself and its fit should not be overlooked. A misaligned hinge, a deformed latch or a fatigued plastic part may be enough to prevent the assembly from completing its travel. It is a more mechanical than electronic fault, but its end result is the same: the washing machine does not authorise the cycle.
| Code | Description | Cause | What usually fails | Severity |
|---|---|---|---|---|
| E45 | Problem with the door lock or with its detection by the electronics | Defective door interlock, damaged wiring, loose connector or fault on the control board | Door lock, wiring harness, lock triac or electronic module | Medium-high, because it prevents the wash cycle from starting |
How to diagnose it without wasting time
The first useful step is to calmly observe how the door behaves. It should close firmly, without unusual play or abnormal resistance. If the latch does not engage properly or the locking click is weak, the problem may be in the locking mechanism or in the alignment of the front panel itself. Before thinking about the board, the visible causes must be ruled out.
It is then worth checking the accessible wiring around the lock, always with the appliance disconnected from the mains. A partly loose connector, one that is blackened or showing signs of overheating already provides a fairly clear direction for the diagnosis. When there are heat marks, the nearby component has usually been working at its limit and it is common for the fault to return even after superficial handling.
If the mechanical side appears to be correct, attention shifts to the electronics. At that point, you are entering the realm of technical repair: checking continuity, inspecting the lock input and testing the board. This is not a fault to improvise with, because the locking system is part of the appliance’s safety features and an incorrect reading can leave the washing machine locked or, worse still, make it operate without reliable confirmation that the door is closed.
Which solutions really tend to work
When the source is the door interlock, the most reliable solution is usually to replace that part. It is a component subjected to repeated use and its failure fits the symptoms of the code well. In many cases, replacing the lock restores normal operation without needing to touch the rest of the system, provided the wiring and board are in good condition.
If the problem comes from a broken wire or damaged connector, the repair focuses on restoring electrical continuity. It may seem like a minor intervention, but in these appliances a clean connection is worth more than a rushed replacement. Fixing a poor connection in time prevents a chain of faults, especially if it has caused overheating around the locking system.
When the diagnosis points to the control module, the repair requires electronic intervention. Depending on the model and the condition of the board, the affected circuit can be repaired or the module can be replaced with a reconditioned or equivalent unit. This option makes sense when the fault is clear and the rest of the washing machine is in good condition, because it avoids replacing parts unnecessarily.
If the damage is mechanical, a misaligned hinge or a poorly seated door can also be corrected. These are less noticeable adjustments, but they are often decisive. The important point is not to confuse a locking error with a fault in the motor, pump or water-level sensor: E45 follows a different path and deserves an accurate assessment from the very beginning.
What to do and what not to do while the fault remains active
Forcing the door shut with excessive pressure usually does not help and may worsen the alignment of the mechanism. It is also not advisable to keep trying to start consecutive cycles if the code appears immediately, because each attempt repeats the same failed check and provides no new information. The machine has already carried out its basic diagnosis: it does not trust the lock.
Unplugging the appliance for a few minutes may help rule out a temporary electronic lock-up, but it should not be taken as a definitive solution. If the error returns, the fault is established in a component or connection. The repetition of the code is a technical clue, not a coincidence.
It is also sensible to check whether the washing machine is properly levelled. A twisted chassis or a forced installation can put the door under strain at an awkward angle and make it difficult for the lock to engage. Sometimes the physical environment around the appliance matters more than it seems: an uneven floor, a tensioned front panel or a worn hinge is enough to trigger the warning.
Why the electronics so often appear in this fault
In modern models, the door is no longer just a mechanical part: it is an electrical command that the board interprets before allowing the wash cycle to proceed. This dependence means that any weakness in the circuit is translated into an immediate stop. The system works like a strict traffic light; if it does not see the correct signal, it does not let anything through.
That is why the error may initially seem like a simple locking issue, while there are actually more layers behind it. The module receives the signal, validates it and decides whether the cycle can continue. If the lock triac or the associated input fails, the information arrives distorted or does not arrive at all. The fault may be in the door, but it may also be in the brain supervising it.
This logic explains why some repairs involve working on the module rather than just replacing the lock. When the board misinterprets a real signal, replacing only the lock may not solve anything. That is why a proper diagnosis does not stop at checking whether the door closes; it looks for the point where the complete circuit between the mechanical action and the electronic response is broken.
A fault that appears minor, but is very specific to diagnose
E45 has one advantage for the technician and one disadvantage for the user: it is a fairly limited fault. It does not involve multiple systems or open up an enormous range of possibilities. It points to the door, its lock or the electronics that validate it. This precision speeds up the repair when interpreted correctly, but it can also be misleading when it is mistaken for a simple door that has not been closed properly.
The most useful interpretation is simple: if the door does not lock reliably, the washing machine protects itself and stops the cycle. If the lock appears to be working correctly, the problem is usually further inside, in the wiring or on the board. The fault is not in the water, the drum or the drain: it is in the access safety chain.
That is why the correct diagnosis saves time and parts. An appliance displaying E45 does not call for endless patience, but for an orderly inspection of the lock, connectors and electronics. When each part is examined in its proper place, the solution stops being a detour and becomes a precise repair, with a much clearer logic than it may seem at first glance.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine4 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















