Daewoo
Daewoo washer E6 error: causes and safe checks
A practical guide to the likely causes, safe checks and model differences behind this washer fault.

An E6 display on some Daewoo washers signals an emergency motor or drive-system fault, sometimes triggered by a jammed drum or clothing caught near the door seal. The code is not universal across every model, so check the full model number before assuming a component has failed; stop using the washer if the error returns or the drum will not turn freely.
If you have a problem with your washing machine, you can use our free error code finder. There, you can identify and troubleshoot errors easily and effectively.
What the E6 display can indicate
On applicable electronically controlled Daewoo washing machines, E6 is associated with an EMG, motor-current or drive-system fault. The control system has detected an abnormal condition and may stop the cycle to prevent further operation. In some cases, the trigger is mechanical: a heavy load, a drum that cannot rotate normally or fabric wedged between the drum and the rubber door gasket.
Other possible causes are less visible. A motor, its wiring or the electronic drive and control components may be malfunctioning. The display alone cannot distinguish a temporary obstruction from an electrical fault, and it does not prove that the motor or control board needs replacement. Those parts require model-specific testing by a qualified appliance technician.
Daewoo has used different control platforms across models, generations and markets. That means the meaning of E6 must be confirmed against the washer’s exact model documentation. Some service information associates the code with abnormal motor current or an EMG condition, while other platforms may use a different diagnostic scheme. Similar-looking codes are not interchangeable between brands or even between all Daewoo models.
Safe checks before arranging internal diagnosis
First, stop the cycle and switch the washer off. If the plug is accessible without moving a heavy appliance or touching a wet area, disconnecting it before checking the laundry is a sensible precaution. Do not remove panels, reach into internal mechanisms or inspect electrical connectors. The safe, user-level check is limited to the drum opening and the load.
Look around the visible edge of the door gasket for a garment caught between the seal and drum. A sleeve, sheet or small item can be pinched there and create resistance or noise as the drum turns. Remove only fabric that is readily accessible, without pulling hard on the seal or reaching into the gap. If the item is trapped or the gasket is damaged, leave it for a technician.
Once the machine is off and the door can be opened normally, check whether the laundry has bunched to one side or the drum is heavily overloaded. Remove some items if necessary and redistribute the remaining load evenly. Bulky bedding can gather into a dense lump during a spin, while a single heavy item may be difficult for the washer to balance. Follow the load limits and cycle guidance in the manual for that model.
With the washer empty and switched off, the drum may be gently turned by hand if it moves freely and the manual does not advise otherwise. Noticeable binding, scraping, grinding or a drum that will not turn is a reason to stop. Do not force the drum or run another cycle to test it; persistent resistance can point to a mechanical problem beyond an accessible clothing obstruction.
Why the code may return after a reset
A brief power reset can sometimes clear a temporary electronic interruption, but it cannot repair a jammed mechanism, damaged wiring or a failing motor-drive component. If the manufacturer’s instructions permit it, switch the washer off, wait briefly and restore power using the normal controls. Do not repeatedly reset the appliance or keep restarting a cycle after E6 reappears.
If the code returns as soon as the drum begins to move, the control may be detecting the same abnormal motor condition again. If it appears only with a large or uneven load, the load may be contributing, but that pattern does not rule out a developing mechanical fault. Repeated E6 after correcting an obvious obstruction calls for model-specific diagnosis, not trial-and-error replacement of parts.
Record when the error occurs: at the start of the cycle, during washing, or as the washer tries to spin. Also note any unusual sound, whether the drum turns by hand when the appliance is off, and whether the code appears with an empty drum. This information helps narrow the fault without opening the machine or performing electrical tests.
Other Daewoo codes and model differences
Daewoo diagnostic codes cover several systems, including water supply, drainage, balance, motor operation, water-level sensing and heating. The table gives common descriptions reported for applicable platforms; it is an orientation aid, not a universal decoding chart. The model manual takes precedence over a general code list, especially when the display uses a different format or prefix.
| Code | Common description on applicable models | Context and likely system |
|---|---|---|
| IE | Water inlet or input fault | Water supply, inlet hose or filling system |
| OE | Drainage or output fault | Drain hose, accessible filter or drain system |
| UE | Unbalanced load | Laundry distribution or washer stability |
| E2 | Overflow condition | Water inlet or water-level sensing system |
| E4 | Leakage or unexpected water loss | Water-containing parts or level detection |
| E5 | High-voltage or drive-system fault on some platforms | Motor drive and electronic control |
| E6 | Motor-current, EMG or drive fault on some platforms | Motor operation, obstruction or drive electronics |
| E7 | Motor direction or Hall-feedback fault on some platforms | Motor feedback and control system |
| E8 | Motor operation or initial motor failure | Motor, feedback or drive system |
| E9 | Water-level or pressure-sensing fault | Pressure sensor and its sensing path |
| H2 | Wash-temperature sensor fault | Thermistor and its circuit |
| H4 | Abnormally high wash temperature | Temperature sensing or heating control |
| H6 | Wash-heater fault | Heating system and temperature rise |
| H8 | Heater overheating or heating without adequate water | Water-level detection and heating system |
Even within this set, definitions and detection thresholds can vary by platform. Older DWD-series information, for example, uses codes such as IE, OE, UE, E2, E4 and several H-series heating codes. Some newer Daewoo-branded models instead use an Er-style series, including door, water-level, pump and excessive-water alerts. A code list for one generation should not be treated as a definitive guide to another.
For the same reason, an E6 shown on a Daewoo washer should not be interpreted using a code chart for another manufacturer. Before ordering a part or deciding that the motor has failed, identify the exact model and consult its user documentation. The product label is commonly found around the door opening or on the rear or side of the appliance, though its location varies.
When a technician needs to take over
Internal diagnosis is appropriate when the drum remains stiff, the error persists with a balanced or empty load, or the washer makes a grinding, scraping or burning sound. Motor-current measurements, inspection of internal wiring and testing of the inverter or control board involve electrical hazards and require suitable training and equipment. Do not remove the cabinet or test live components.
A technician can use the model-specific service information to determine whether the cause lies in the motor, feedback sensor, wiring, drive electronics, mechanical parts or control board. Replacing the PCB simply because E6 appears can be costly and may leave the original problem unresolved. A sound diagnosis checks the relevant systems before identifying a failed component.
Stop using the washer and keep it switched off if you notice smoke, a burning smell, visible arcing, a damaged power cord or water near electrical parts. If there is uncontrolled water entering or leaking, use an accessible household shutoff only if it can be reached safely; do not move or dismantle the appliance to get to it. These signs require professional attention rather than another cycle.
What to note for an accurate diagnosis
Write down the exact display, including any letters, spaces or additional digits, and record the washer’s complete model number. Note the cycle stage when E6 appears, the amount and type of laundry, and whether the drum turns freely when the machine is off. These details help distinguish a load-related event from a recurring motor or drive fault.
Also record whether the fault began after a loud impact, a move, an interrupted cycle or a visible obstruction at the door seal. Do not infer that a particular event caused the failure, but include it as context. If the error clears once and returns later, that is useful information too; a temporary reset is not evidence that the underlying issue has been repaired.
An E6 indication is a starting point for diagnosis, not an automatic instruction to replace a motor or board. A trapped garment or uneven load may be simple to correct when it is fully accessible, while a recurring code can involve components that are unsafe to inspect at home. Use the model-specific meaning, make only external checks and leave internal electrical or motor-drive work to a qualified technician.
More error codes: Daewoo Washer Error Codes.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Oven7 days agoWhirlpool oven F01 error: what it means and what to do
Coffee machine4 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine4 days agoJura coffee machine error 8: what to do and repair costs
Coffee machine4 days agoSaeco coffee machine error 1: what it means and what to do
Microwave6 days agoSiemens microwave error 1007: what to check and when to stop
Microwave6 days agoError 2 on a Whirlpool microwave: causes and what to do
Oven6 days agoE05 error on a Siemens oven: how to respond safely
Coffee machine4 days agoPhilips coffee machine error 1: causes and safe cleaning
Fridge5 days agoLG fridge FF error: what it means and what to do
Coffee machine4 days agoSaeco error 5: causes and checks without taking it apart
Beko5 days agoBeko fridge E4 error: what it means and what to do
Bosch6 days agoBosch microwave E3 error: causes and safe checks





















