Connect with us

Miele

Miele washer F105 error: what it means and what to do

Understand the likely source of this temperature fault, what the display can tell you and where safe troubleshooting should stop.

Published

on

Miele washer F105 error: what it means and what to do

Imagen: DariuszSankowski / Pixabay

On a Miele washing machine, F105 generally points to a problem with the temperature reading for the steam generator, often involving its NTC sensor or the circuit that carries its signal. The washer may stop a cycle when it can no longer rely on that reading; the cause could be the sensor, internal wiring, the heater or the control electronics, so the code alone does not identify a part that should be replaced.

If you have a problem with your washing machine, you can use our free error code finder. It can help you identify and understand appliance error codes.

What F105 indicates on a Miele washer

The NTC, short for negative temperature coefficient, is a temperature sensor whose electrical resistance changes as its surroundings get warmer or cooler. The washer’s control system uses that change to monitor the steam generator. When the signal falls outside the range the electronics expect, or appears open or shorted, the system may register F105 and interrupt the relevant part of the program. The fault therefore concerns the steam generator’s temperature-measurement circuit, rather than a general problem with the drum, water supply or door.

That distinction helps explain why the machine can look normal from the outside while still refusing to continue. The display, door lock and drum may respond, but the control board cannot safely rely on the temperature information it needs for a steam or heating stage. A stopped cycle is the washer’s way of avoiding operation without a dependable thermal reading; it is not proof that the heater itself has failed.

F105 should be treated as a clue, not a universal diagnosis for every Miele model. Error definitions and service procedures can vary across product generations and model ranges, and the information shown for one washer should not automatically be applied to another. Check the model-specific manual or appliance documentation if available, especially if the display shows additional symbols or the code behaves differently from the description here.

How the fault may appear during a cycle

The timing of the alert can help a technician narrow down the possibilities. If F105 appears as soon as a program begins, before any steam or heating phase, an electrical connection, sensor signal or control-system fault may be involved. That timing does not prove that the electronic board is at fault, but it gives a different diagnostic clue from a code that appears only after the washer has tried to warm the steam generator.

If the warning appears as the machine reaches a heating or steam stage, the NTC sensor or heating assembly may move higher on the list of possibilities. A sensor can behave inconsistently as its temperature changes, while a heater problem can affect how the system warms up. The point in the cycle when the code appears is useful context, not a reliable substitute for measurements or a complete inspection.

An intermittent alert can be especially difficult to interpret. A loose or deteriorating internal connection may produce a signal that comes and goes, but a one-time occurrence does not establish that explanation. Note whether the washer was starting, heating or generating steam when the message appeared, whether it repeated after a reset and whether the cycle stopped in the same place. That history can make professional diagnosis more focused without requiring the user to open the machine.

Likely causes behind the temperature warning

A damaged or worn NTC probe is one of the main possibilities described for this fault. It may send a reading that is inconsistent with the actual temperature, or its circuit may appear open or shorted to the control system. Because the failure can be internal, the sensor’s visible condition would not necessarily reveal whether it is working correctly. A proper assessment relies on model-specific electrical measurements, not appearance alone.

Internal wiring and connectors are another possible source. A loose contact, corrosion, moisture or a cable damaged by heat or movement can interrupt or distort the sensor signal. Condensation around a steam-generating assembly and repeated temperature changes may contribute to wear over time, but the presence of moisture or frequent steam use does not by itself confirm the cause. Those connections are inside the appliance and should be left undisturbed by the owner.

The steam generator’s heating element may also be involved, as can the control board that reads the sensor and manages the heating process. A failing heater can create abnormal thermal behavior, while a damaged relay, solder joint or circuit path may prevent the control electronics from interpreting the signal correctly. Several parts share the same temperature-control chain, which is why replacing the NTC based only on the code can miss a wiring, heater or board fault.

Limescale, condensation and heavy use are possible contributing conditions, particularly in appliances that regularly run steam programs, but they should not be mistaken for a confirmed diagnosis. The reference information does not establish one guaranteed cause or a fixed repair cost for F105. A technician needs to identify the failed component and check whether related parts have also been affected before recommending a repair.

CodeDescriptionCauseWhat it suggests
F105Temperature-reading fault associated with the steam generatorPossible NTC sensor, internal connection or wiring, heater, or control-board problemThe thermal-control circuit needs model-specific diagnosis

What the timing and symptoms can tell you

The display gives only part of the story, so observations made during ordinary use can be helpful. A fault that appears repeatedly at the same point may indicate that the washer reaches a particular stage and then rejects the temperature signal. If it appears immediately, the machine may be detecting a problem before heating begins. Neither pattern identifies a failed component on its own, but both are more useful than a vague report that the washer stopped.

Pay attention to whether the cycle completes, whether steam functions are unavailable and whether the fault returns after the machine has been reset. It may also help to note whether the washer was unusually hot, whether a burning smell was present or whether there are visible signs of damage outside the appliance. Do not run repeated programs just to reproduce the code, particularly if the washer smells burnt, behaves unusually hot or shows any sign of electrical damage.

F105 is not, by itself, evidence of a water-supply blockage or a drain obstruction. Those problems have different symptoms and may generate different codes, depending on the model. Avoid treating every stopped cycle as the same kind of fault: the message points toward the temperature-control system, and troubleshooting unrelated filters or hoses is unlikely to resolve an internal sensor or electronics issue.

Safe checks at home and the limit of DIY troubleshooting

For an owner, the safest first step is to stop the program and consult the manual for the exact washer model. If there is no burning smell, visible damage, leak or other warning sign, a single reset may be reasonable: switch the appliance off using its controls and, only if the plug is readily accessible and the area is dry, disconnect it from the outlet briefly before restoring power. Do not pull on a damaged cord, touch a plug with wet hands or move a heavy washer to reach an outlet.

After restarting, observe whether the code clears and whether it returns during the same stage. A reset can clear a temporary control glitch, but it cannot repair a faulty sensor, heater, damaged wire or electronic board. If F105 returns, stop treating resets as a solution and avoid repeatedly starting steam or heating programs in an attempt to make the message disappear.

Do not remove panels, reach inside the cabinet, unplug internal connectors, test components with a multimeter or inspect the control board. Those tasks expose internal electrical parts and can create a shock or injury risk, even when the washer appears switched off. The source material describes measurements of the NTC and heater as diagnostic steps, but they require technical skill and model-specific information; they are not safe owner checks. Internal electrical diagnosis belongs with a qualified appliance technician.

There is little useful external cleaning to perform for this particular code. Accessible detergent drawers and ordinary user-maintenance areas can be cared for as described in the manual, but cleaning them is not a repair for a steam-generator temperature fault. Never spray liquid into openings or use improvised cleaners around electrical controls. If the machine has a visible leak, stop using it and follow the manual’s safety instructions rather than attempting to access internal parts.

When professional diagnosis is appropriate

Arrange a qualified assessment if F105 returns after one safe reset, appears immediately whenever the machine is switched on, or repeatedly interrupts a heating or steam stage. The same applies when steam functions do not work as expected or the washer stops in a consistent pattern. A persistent warning means the temperature-control system is still detecting an unreliable signal, even if the rest of the appliance appears to operate normally.

A burning odor, dark marks, discoloration, unusual heat or visible damage calls for a more cautious response. Switch the washer off, do not restart it, and avoid touching damaged cords or wet areas. If the plug is safely reachable without moving the appliance or approaching water, disconnecting it may be appropriate; otherwise, leave it off at the controls and seek qualified help. Do not open the washer to look for burnt components, since a visual check inside can expose hazardous parts and may not reveal the actual failure.

A technician can test the NTC response against the manufacturer’s model-specific criteria, inspect the associated wiring and connectors, assess the heating element and determine whether the control board is processing the signal correctly. These checks help distinguish a failed sensor from a break elsewhere in the circuit. An apparently sound part can still fail under operating conditions, while a visibly damaged component may not be the original cause of the problem.

The repair may involve a sensor, a connector or wiring, the heating element, or the electronic control board; the required work depends on the diagnosis. The code does not establish a standard price, parts cost or repair time, and no dependable estimate can be made without the washer’s model and findings. Testing the full circuit before replacing parts helps avoid guesswork and reduces the chance of paying for a component that was not responsible.

Why continued use is not a good workaround

A washer that cannot trust its temperature reading may stop a cycle or fail to complete a steam-related stage. That can leave laundry unfinished and make programs unpredictable. More importantly, temperature control is part of how the appliance manages heating; continuing to run the machine despite a recurring fault does not restore the missing measurement. The safest response to a persistent F105 is to stop relying on the affected function until the cause has been assessed.

It is not possible to conclude from the code alone that the washer will overheat or that another component has already been damaged. Those outcomes depend on the actual fault and the model’s control behavior. Still, a poor connection or failing heating component can worsen if repeatedly operated, while a control-board problem may remain unresolved no matter how many times the machine is restarted. The warning deserves attention without assuming the worst.

If the code appeared once and clears after a reset, keep a note of the circumstances and watch for a recurrence rather than dismantling the appliance or replacing parts. If it returns, the pattern and timing can help a technician. One isolated reset is different from repeatedly overriding a persistent fault; the latter can obscure useful symptoms and expose the machine to further abnormal operation.

A clear reading of the warning is the best starting point

F105 on a Miele washer generally directs attention to the steam generator’s temperature-reading circuit, especially the NTC sensor and its connections. The heater and control electronics are also possible causes, so the code identifies an area to investigate rather than naming a definitive failed part. That distinction matters: an accurate repair depends on tracing the signal through the system, not changing the first component associated with the message.

At home, keep the response limited to the manual, a cautious one-time reset when conditions are safe and careful observation of when the warning returns. Leave internal wiring, electrical measurements, heater checks and board repairs to a qualified technician. Taking the code seriously while respecting that safety boundary gives the washer a better chance of receiving the right diagnosis without turning a stopped cycle into a riskier problem.

More error codes: Miele washing machine error codes: what they mean and what to do.

This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.

Most read