Heat pump
Vaillant heat pump 01 message: meaning and safe checks
An 01 message alone is not a diagnosis. The full code and exact model determine what to do next.

An 01 message on a Vaillant heat pump does not identify a specific fault without the full code and the exact equipment model. The available aroTHERM information does not establish a verified meaning for that number alone: there is no basis for immediately blaming low pressure, a sensor or the compressor. Before resetting anything, photograph the display and check for letters, decimal points or additional digits. Those details can completely change the diagnosis and prevent unnecessary work.
If you have a problem with your heat pump, you can use our free error code finder. There you can identify errors and find clear, practical troubleshooting information.
The number 01 needs its display context
The first distinction is between a number appearing on a display and a fault identified by the system. A controller can show temperatures, settings, operating states and messages from different units. Without seeing the display and checking the relevant manual, you should not assume that every 01 is a fault code. Nor should you mentally add an F or fill in missing digits to make the number match a table found online.
The aroTHERM fault information covered by the available reference material includes codes such as F.022, F.073 and F.094. Another listing presents equivalent descriptions under F.22, F.73 and F.94. This difference in formatting does not establish that every variation is interchangeable across all equipment: the exact model’s manual remains the deciding reference. It certainly does not justify turning an isolated 01 into one of those faults.
Identification should also establish where the message appears. A number shown on the home’s heating controller is not necessarily the same as one displayed on the hydraulic module or another part of the system. The outdoor unit, indoor module and controller perform different jobs, even though they belong to one installation. Recording which display shows the message helps interpret it without automatically blaming the outdoor heat pump unit.
The details that clarify a fault without dismantling anything
A clear photograph preserves details that often disappear when someone writes a message down: a decimal point after a letter, a leading zero, a warning symbol or accompanying text. If the display alternates between messages, recording that sequence is useful too. The aim is to preserve the message exactly as displayed, rather than an approximate interpretation. Collecting this information does not require entering installer menus or changing parameters.
The aroTHERM product name is not a substitute for the full model reference. Vaillant supplies different configurations, including aroTHERM plus and systems with uniTOWER, and they should not be assumed to share every message or procedure. Check the handover documents or a visible label without removing covers. Identifying the controller fitted to the system is also useful, particularly when the number appears only on its screen.
The system’s behavior provides another part of the context. Heating may stop while hot water remains available, or both services may stop; alternatively, only a particular cylinder-heating request may fail. These situations do not establish on their own which component is faulty. They do help describe the incident more accurately and distinguish a system-wide shutdown from a problem affecting one function or a controller setting.
A rapid domestic hot water function that does not respond is not confirmation of an assumed 01 fault either. Its behavior depends on the equipment and the installation’s configuration. Accounts involving other heat pumps, even from the same brand, do not justify connecting electric heaters or changing technical settings. Similar symptoms can have different causes in different installations, and importing another system’s solution can create an additional problem.
The aroTHERM codes that can guide a diagnosis
The following table brings together the codes included in the available technical reference information. It helps distinguish groups of faults, but does not replace model-specific verification: detection conditions and the applicability of each message can vary between generations. The isolated 01 is included specifically to show that the material does not establish a corresponding meaning. The causes described are diagnostic possibilities, not instructions to replace particular parts automatically.
| Code | Description | Cause or associated condition | Safe check or professional action |
|---|---|---|---|
| 01, with no further information | Meaning not confirmed for the specific equipment. | Display context, full code or model identification is missing. | Photograph the message and check the model-specific manual. |
| F.022 / F.22 | Insufficient pressure in the home’s water circuit. | Possible leak, air in the circuit or defective pressure sensor. | Read the visible pressure indication; do not refill or bleed the system by trial and error. |
| F.042 | Outdoor unit identification problem. | Coding resistor damaged or incorrectly fitted. | Internal diagnosis by a technician. |
| F.073 / F.73 | Water pressure sensor signal fault. | Disconnected sensor or short-circuited input. | Professional inspection of the sensor and its connections. |
| F.094 / F.94 | Vortex flow sensor fault. | Disconnected or short-circuited input. | Professional inspection; this does not necessarily mean water flow is absent. |
| F.103 | Incompatible electronic circuit board. | Outdoor unit board does not match the model. | Verification by a technician. |
| F.514 | Compressor inlet temperature sensor fault. | Disconnection or short circuit. | Professional intervention. |
| F.517 | Compressor outlet temperature sensor fault. | Disconnection or short circuit. | Professional intervention. |
| F.519 | Water return temperature sensor fault. | Disconnection or short circuit. | Professional intervention. |
| F.520 | Water flow temperature sensor fault. | Disconnection or short circuit. | Professional intervention. |
| F.526 | Electronic expansion valve outlet temperature sensor fault. | Disconnection or short circuit. | Professional intervention. |
| F.546 | High-pressure signal fault. | Disconnected sensor or short-circuited input. | Professional diagnosis; this is distinct from confirmed excessive pressure. |
| F.582 | Electronic expansion valve problem. | Incorrect connection or damaged coil cable. | Professional intervention. |
| F.585 | Condenser outlet temperature sensor fault. | Disconnection or short circuit. | Professional intervention. |
| F.703 | Low-pressure signal fault. | Disconnected sensor or short-circuited input. | Professional diagnosis of the measurement system. |
| F.718 | No rotation confirmation from fan 1. | Blocked fan or missing rotation signal. | Observe from outside without touching blades or inserting objects. |
| F.729 | Compressor outlet temperature too low. | The reference specifies more than 10 minutes below 0°C or a drop below −10°C. | Model-specific professional checks. |
| F.731 | High-pressure protection activated. | Excessive refrigerant pressure; the reference places activation at approximately 41.5–42.5 bar. | Professional intervention; this is not the heating water pressure. |
| F.732 | Compressor outlet temperature too high. | The reference specifies a value above 110°C. | Professional diagnosis. |
| F.733 | Evaporation temperature too low. | Possible insufficient airflow or low refrigerant charge. | Look for external obstructions; refrigerant circuit work is for a qualified technician. |
| F.734 | Condensation temperature too low. | Heating circuit conditions or low refrigerant charge. | Professional diagnosis. |
| F.735 | Evaporation temperature too high. | Conditions outside the compressor’s operating range. | Professional diagnosis. |
| F.737 | Condensation temperature too high. | Excessive temperature or insufficient water flow. | Professional assessment of operating conditions. |
| F.741 | Water return too cold during defrosting. | The reference specifies a temperature below 13°C. | Professional inspection of the installation. |
| F.752 | Frequency inverter fault. | Internal electronic fault or voltage outside the 70–282 V range stated in the reference. | Electrical checks by a qualified professional only. |
| F.753 | Inverter communication fault. | Communication interrupted with the outdoor unit circuit board. | Professional diagnosis of electronics and connections. |
| F.755 | Incorrect four-way valve position. | In heating mode, flow temperature is below return temperature. | Professional intervention. |
| F.774 | Air inlet temperature sensor fault. | Disconnection or short circuit. | Professional intervention. |
| F.785 | No rotation confirmation from fan 2. | Blocked fan or missing rotation signal. | Do not touch the fan; professional inspection required. |
| F.788 | Water circuit pump blocked. | Dry running, blockage, overvoltage or undervoltage detected. | Professional diagnosis; do not attempt internal unblocking. |
| F.817 | Fault involving the compressor and inverter. | Defective compressor, inverter or connection between them. | Establish the cause before deciding on replacement. |
| F.818 | Inverter supply problem. | Incorrect voltage or supply blocked by the electricity provider. | Professional diagnosis and a check for relevant supply notifications. |
| F.819 | Inverter overheating. | Excessive internal temperature. | Professional intervention. |
| F.820 | No rotation signal from the water pump. | Outdoor unit does not receive operating confirmation. | Professional diagnosis of the pump and signal. |
| F.821 | Backup electric heater flow sensor fault. | Immersion heater sensor disconnected or both flow sensors defective. | Professional intervention. |
| F.823 | Hot gas thermostat activated. | Excessive refrigerant temperature. | Professional refrigerant circuit intervention. |
| F.824 | Low pressure in an intermediate circuit. | In installations with a second heat exchanger: leak, air or defective sensor. | Professional diagnosis of that specific configuration. |
| F.825 | Condenser inlet temperature sensor fault. | Disconnection or short circuit in the refrigerant-side measurement. | Professional intervention. |
| F.1100 | Backup electric heater safety limiter activated. | Possible insufficient flow or air in the circuit. | Do not reset internal safety devices; professional inspection required. |
| F.1117 | Compressor phase fault. | Supply, fuse or connection problem. | Professional electrical checks. |
| F.1120 | Backup heater phase fault. | Poor connections or excessively low voltage. | Professional electrical checks. |
| F.9998 | Loss of eBUS communication. | Connection problem or no power to the outdoor unit. | Professional inspection; do not handle wiring. |
The temperature, pressure and voltage figures describe detection conditions reported for particular equipment; they are not user settings. In particular, the 41.5–42.5 bar associated with F.731 refers to the refrigerant circuit, not the heating water pressure gauge. Confusing these circuits can lead to dangerous action. None of the figures in this table should be used to add water, alter safety protections or test electrical connections.
The table also shows why a code does not always identify a failed part. F.817 can involve the compressor, inverter or their connection; F.073 points to a pressure measurement problem, whereas F.022 describes insufficient pressure. The message identifies a condition detected by the controller, but the underlying cause still needs checking. Buying a sensor or agreeing to compressor replacement solely on the wording of a message would be premature.
Water pressure, flow and sensors are different issues
A low-pressure reading and a sensor fault may look similar to someone facing a stopped system. However, they require different diagnoses. With a confirmed insufficient-pressure code, you can read the pressure shown by the equipment or an accessible gauge and compare it with the manual. Without the exact model and installation details, there is no universal pressure that can appropriately be recommended as the solution.
Household checks stop at observation. Look for visible dampness around the units or accessible pipework without dismantling joints or touching electrical areas. If water is present near electrical connections or the equipment’s electrical panel, do not approach or handle that area. Refilling, bleeding or working on hydraulic components means intervening in a potentially pressurized circuit; a professional should determine the appropriate action.
Flow describes water movement, not static pressure. An installation can therefore show apparently normal pressure and still report a circulation-related problem. Likewise, a Vortex signal fault does not automatically prove that the pump is failing to move water. This distinction prevents two mistakes: adding water unnecessarily and replacing a pump before establishing whether circulation or its measurement is faulty.
External checks have a clear boundary
You can review the operating mode, schedule and requested temperature through the controller’s normal user controls. A home receiving no heat does not, on its own, prove a compressor fault. An inactive schedule or a demand that has already been met may explain the lack of operation without any failure. These checks help distinguish an absence of heating demand from a shutdown accompanied by a fault message.
From a safe position, look for objects, vegetation or accumulations obstructing airflow around the outdoor unit. Only remove loose items from the surrounding area when this does not require approaching moving parts, removing grilles or touching the equipment. If ice is attached to the unit, do not strike it or apply improvised heat. Inspection must remain visual, with no internal access, even if the fan appears to have stopped.
Internal filters, connections and service valves are not an extension of that visual inspection. Neither is using a multimeter or opening a cover to look for a loose wire. aroTHERM plus units use R290, a flammable refrigerant, reinforcing the need to leave refrigerant circuit work to qualified personnel. The practical boundary is straightforward: no covers, wiring or refrigerant should be involved in household checks.
A reset does not prove the problem has gone away
Only reset the system through the user procedure specified for the model, and record the message first. If the manual does not provide for that action for the displayed warning, do not improvise power disconnections. Clearing the indication does not repair its cause: the system may need to reach particular conditions again before detecting it. What matters is whether the fault returns and when it occurs during operation.
Repeated resets to force heating or hot water are not a valid equipment test. If the system locks out again, stop retrying and arrange a technical assessment. This is particularly important when the message concerns refrigerant pressure, compressor temperature, water circulation or electrical protection. Never bypass a lockout or enable backup operation through installer settings: a safety protection is not an obstacle to work around.
Hot water still coming from the tap does not establish that the whole system is working correctly: the cylinder may retain water heated before the fault. Likewise, heating that remains active does not establish that every other service can be used without knowing the fault. Until the message has been identified, safe operation cannot be guaranteed across all modes. If there is a burning smell, smoke, electrical tripping or a visible leak, do not carry out further tests.
Diagnosis should come before spending on parts
No reliable repair price can be inferred from an isolated 01. A configuration issue, an incorrect reading and a compressor failure have very different implications. Before authorizing work, the estimate should distinguish diagnosis, labor, materials and any callout charges. It is also worth establishing whether the visit costs extra or is credited against an accepted repair, rather than assuming either arrangement applies.
If the equipment has warranty coverage or a maintenance agreement, check the claims process before authorizing outside work. Opening the unit or fitting a separately purchased part can complicate the assessment of responsibility and damage. It would be wrong to claim that any opening automatically cancels all coverage, but it is sensible to check the terms before intervening and retain photographs of the message and maintenance records.
The choice between repair and replacement should not rest solely on equipment age or the name of a component appearing on the display. Relevant factors include the confirmed diagnosis, overall condition, previous failures and the full cost of an equivalent replacement system. If compressor or circuit board replacement is proposed, the explanation should state which checks ruled out other possible causes. An expensive proposal needs a diagnosis, not merely an interpretation of a number.
Identifying the display message prevents guesswork repairs
To report the problem accurately, keep the full code, equipment reference and a description of what has stopped working. Recording when it appeared and whether it coincided with a power interruption or recent work can guide the inspection without proving a cause on its own. That information provides a useful starting point and reduces the risk of preparing a repair for a different fault.
The next action depends on the confirmed message. If the manual allows a schedule to be corrected through normal user controls, that falls within everyday operation. If the warning points to internal sensors, electrical supply, pumps, the compressor or the refrigerant circuit, a technician qualified for the equipment and the work should intervene. The boundary is determined not by how simple a part appears, but by the risks and checks involved.
Until that identification is available, 01 should be treated as incomplete information, not a verdict on the heat pump. It does not establish low water pressure, prove a damaged circuit board or justify a refrigerant recharge. The most useful response is to preserve the information, keep checks observational and avoid trial-and-error changes. In an installation with several units, reading the message correctly is diagnostic work, not an insignificant preliminary step.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine7 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Daikin7 days agoDaikin heat pump error codes: meanings and safe checks
Magazine7 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer7 days agoCecotec air fryer E1 error: what to do safely
Magazine7 days agoMan affected by smoke in Valladolid fire
Heat pump6 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine6 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Magazine5 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















