Magazine
Why isn’t my air conditioner cooling properly and what should I check first?
Air conditioning may stop cooling due to dirty filters, lack of gas, or technical failures. Learn to detect the cause and prevent breakdowns.

When an air conditioner turns on, makes noise, moves the louvers, and still leaves the room like a sauna with a remote control, the failure is usually in a quite specific point: lack of airflow, poor configuration, dirt, a blocked outdoor unit, a leak of refrigerant gas, or a malfunction in the compressor, the sensor, or the electronics. It’s not always an expensive tragedy. Sometimes, it’s enough to clean the filters and check that the unit is in cool mode. Other times, however, it’s wise to set aside domestic pride and call a certified technician, especially if there is ice in the pipes, the air is warm for hours, or the unit has gradually lost performance.
The first filter is simple: check that the remote is set to cooling, that the selected temperature is below the ambient temperature, that the fan is not on minimum speed, that the dirty filters don’t look like an old carpet, and that the outdoor unit can breathe. Manufacturers like Daikin, Mitsubishi Electric, or LG usually point out these same causes as the most common: clogged filters, incorrect mode, refrigerant loss, electrical problems, thermostat misadjustment, or insufficient ventilation for the condenser. It’s not black magic. It’s domestic physics, dust, and a bit of maintenance that almost all of us leave for when the heat has us backed against the wall.
If you have a problem with your air conditioner, you can use our free error code finder. From there, you can easily and effectively find out and solve all the errors.
The deceptive symptom: it seems to work, but it doesn’t cool
The air conditioner has a very contemporary virtue: it can appear normal while failing at the essential. The screen lights up, the domestic split blows, the remote obeys, and the outdoor unit may emit its low hum, as if everything is in order. But the living room doesn’t drop below 28 degrees. That’s where the confusion begins. The user hears air and thinks cold. It’s not the same. A fan also moves air, and no one attributes Nordic powers to it.
In a heat pump or split air conditioning system, the cold doesn’t come from within the unit as if it were a magical refrigerator stuck to the wall. The unit extracts heat from the inside and expels it outside through a refrigerant circuit. The indoor unit takes hot air from the room, passes it through a cold exchanger, and returns it cooler. The outdoor unit does the less glamorous part: dissipating heat outside, with sun, dust, fluff, leaves, drying racks, pots, and that Spanish urbanism that sometimes fits machines into patios where even a folding chair wouldn’t fit.
That’s why the diagnosis doesn’t start with “it’s low on gas,” even though it’s the most repeated phrase. It starts with airflow. If the air doesn’t circulate well through the filters, through the evaporator, or through the outdoor unit, the equipment loses performance even if the circuit is charged. A clogged filter reduces flow and forces the unit to work harder; if dirt accumulates, thermal exchange worsens, consumption rises, and the sensation in the room is the typical one: air comes out, yes, but without bite. The same unit that froze the living room in June starts blowing a tired breeze in August.
The outside heat also matters. With a heat wave, a poorly insulated home, a closed terrace, or a sun-facing room, the unit may fall short even if it’s not broken. It doesn’t mean that any poor performance is the fault of summer — that wildcard serves for everything and nothing — but a unit just right in cooling power, poorly installed, dirty, or aged will struggle more. That’s where the difference between a well-sized installation and a machine bought “by square meters” like someone buys a carpet becomes noticeable.
The basic check that avoids half an imaginary breakdown
Before thinking about compressors, electronic boards, or gas refills, it’s worth looking at the remote. It seems obvious. It is. And yet, it resolves more annoyances than are admitted aloud. The unit must be in cool mode, not in fan mode, not in dehumidification mode, not on automatic if the sensor is misinterpreting the room. On many remotes, it appears as “Cool,” with the icon of a snowflake. The selected temperature must be below the actual temperature of the room; setting 27 degrees in a room at 28 may activate the compressor little or not at all. Setting 18 won’t make it cool faster either: it will just ask it to work longer and with more stress.
Fan mode is the great impostor. The indoor unit blows, the louvers move, the user feels a draft and thinks the unit cools little. In reality, it’s not refrigerating. It’s just moving the hot air. The dehumidification mode, on the other hand, may provide some relief because it reduces humidity, but it’s not designed to lower the temperature with the same intensity as cool mode. In humid areas —Valencia, Barcelona, Málaga, much of the coastline— that difference is noticeable: sometimes the problem is not just the degree, but the sticky air, that towel-damp heat.
The fan speed can also distort the diagnosis. If it’s on silent mode or minimum, the air may come out cold but at such a low flow that the room takes a long time to notice the change. In large rooms, with high ceilings or direct sun exposure, a speed that’s too low turns the split into a polite whisper. Very fine, very discreet, almost British. But insufficient.
The thermostat deserves its own suspicion. If the temperature sensor is dirty, poorly placed, affected by a draft, or receiving return air that’s already cooled, the unit may think the room is cool when it’s not. The opposite can also happen: it works non-stop because it never detects the actual temperature. In both cases, there’s a discrepancy between what the unit “thinks” and what the human body experiences. And the human body, with 31 degrees in the bedroom, is usually right.
Filters, dust, and outdoor unit: the cheap breakdown is often in plain sight
Dirty filters are to air conditioning what clogged arteries are to the body: everything keeps functioning, but with effort, worse, and increasingly at risk. Dust doesn’t arrive with fanfare. It comes in little by little, sticks, forms a grayish skin, and ends up blocking the airflow. If there are pets, nearby construction, open windows, or heavy nighttime use, the filter loads up faster. In frequently used units, cleaning the filters once a month is a reasonable guideline. Not heroic. Reasonable.
Cleaning is not a mystery, although it’s worth doing it with some calm. Turn off the unit, lift the front cover, remove the filters, remove the dust with a soft vacuum or lukewarm water if the manufacturer allows it, dry them well, and put them back. No mounting them wet, no aggressive products, no scrubbing as if restoring a 1978 blind. Delicate or special filters, like some purification systems, are not always washed: they are replaced according to the manual. That fine print matters.
The outdoor unit is the other great forgotten. It lives outside, which is an elegant way of saying it receives heat, dust, leaves, feathers, urban grease, dirty rain, and, in some patios, the generous contribution of several foreign kitchens. If the outdoor fan doesn’t expel heat well, the circuit loses efficiency. A condenser crammed into a closed terrace, covered by an awning, too close to a wall, or surrounded by junk will have more difficulties. Not because it’s capricious, but because it needs to exchange heat with the environment. If we condemn it to breathe its own hot air, performance drops.
There’s a very clear signal: the outdoor unit starts, but the indoor air doesn’t drop in temperature or takes an eternity. There may be dirt in the condenser, a blocked fan, an electrical problem, or a lack of refrigerant. The accessible part can be visually checked, without disassembling or playing technician with a screwdriver. If there are leaves, bags, cardboard, or superficial dirt around, it’s cleared. If the casing needs to be opened, connections manipulated, or the circuit touched, DIY is over.
Drainage also matters. When the unit cools, it condenses moisture and generates water. If the drain is blocked, it may leak, stop for protection, or operate irregularly. Not always a blockage in the drainage causes it to stop cooling, but it can appear alongside other symptoms: strange smell, moisture on the wall, interior dripping, dirty tray. The air conditioner not only moves temperature; it also moves water, dust, and bacteria if left unattended for months. The unit is not an altar. It needs maintenance.
When ice appears, something is wrong
Ice in the indoor unit, in the pipes, or near the connections is not proof that the unit “is cooling a lot.” It’s a red flag. It may be due to lack of flow from dirty filters, obstructed evaporator, indoor fan problems, or low refrigerant pressure. The result is paradoxical: ice forms, but the room doesn’t cool well. Like a perfect metaphor for so many things: appearance of cold, thermal failure.
When ice appears, it’s reasonable to turn off the unit and let it defrost. It’s not advisable to start it up again and again or scrape the frost. If after cleaning the filters and restoring normal flow it freezes again, we are no longer dealing with a simple cleaning issue. There may be a leak, expansion problem, or ventilation failure. And that’s when the technician comes in.
Refrigerant gas doesn’t run out: it escapes
Few phrases have caused more domestic damage than “it needs gas.” The refrigerant in an air conditioner doesn’t get consumed like gasoline in a car. It circulates through a closed circuit. If it’s lacking, there’s usually a leak or a previous intervention done poorly. Refilling without locating and repairing the leak is a temporary fix that leads to a future bill. The unit may cool for a few days or weeks, but the problem will return. And the released gas doesn’t disappear like cheap perfume: it has environmental impact and is regulated.
In Spain, the handling of fluorinated gases and equipment containing them is regulated. The Royal Decree 115/2017 sets rules for distribution, marketing, handling, leak control, recovery, and certification of personnel performing these activities. The Ministry for Ecological Transition also outlines the certification framework for professionals handling these gases, with different categories depending on the type of equipment and work. It’s not an administrative whim. It’s safety, climate, and responsibility.
The framework of the European Union has tightened with the Regulation (EU) 2024/573, which replaced the previous regulation on fluorinated gases and affects refrigerants, equipment, and service obligations. It may sound distant, very official bulletin and cold coffee, but it conditions the spare parts market, repairs, the availability of certain gases, and the transition to alternatives with lower climate impact. The invisible refrigerator in the living room also belongs to the real world.
How can a possible lack of refrigerant be noticed? The unit cools less and less, the unit runs for a long time without reaching temperature, ice may form in pipes or the indoor coil, strange noises can be heard, or the outdoor machine operates abnormally. The loss of gas is a delicate issue because the refrigerant is the fluid that allows heat to be absorbed from the environment and expelled outside. Without that correct circulation, everything becomes theater: screen, remote, moved air, and little refrigeration.
Don’t confuse “it has gas” with “the circuit is fine.” A system can have refrigerant and still not cool due to poor circulation, expansion valve issues, a fatigued compressor, a dirty condenser, erratic sensors, or electrical problems. The technician shouldn’t just plug in a bottle. They should measure pressures, temperatures, consumption, check connections, look for leaks if necessary, and confirm that the installation operates within parameters. Refilling without diagnosis is like pouring water into a bathtub without a plug. Very active, but also very useless.
Compressor, board, sensors: when the breakdown is no longer at home
The compressor is the muscle of the system. If it doesn’t start, starts poorly, or operates out of range, the air conditioner can ventilate without cooling. Sometimes the user hears the indoor unit and thinks the whole system is active, but the outdoor unit hasn’t really entered cooling mode. Or it enters and stops. Or it tries to start and cuts off for protection. In modern inverter units, the diagnosis may be less evident because the compressor modulates its power and doesn’t always make the abrupt start of older machines.
Electrical failures also have that ghostly aspect. A deteriorated start capacitor, a damaged electronic board, a relay, a loose connection, a defective temperature sensor, or a failed communication between the indoor and outdoor units can leave the equipment in an ambiguous zone: it’s not dead, but it doesn’t cool either. The screen may not show an error code. Or it may, through numbers and letters that the user looks at with the same tenderness as one looks at a tax letter.
When there’s an error code, it’s advisable to take a picture of it before turning everything off. The code guides the technical service and avoids that very common scene: the professional arrives, the unit decides to behave for ten minutes, and no one knows where to start. If the unit turns off by itself, there’s a circuit breaker trip, it smells burnt, makes electrical clicks, vibrates strangely, or the outdoor unit doesn’t spin, there’s no domestic debate: it’s disconnected and a professional is called.
Size and installation also count. An undersized air conditioner can be healthy and still fail to cool a room with a lot of sun, poor carpentry, high ceilings, an open kitchen, or poor insulation. Cooling power is not an aesthetic issue. It depends on square meters, orientation, insulation, number of people, windows, electrical appliances, and local climate. A small unit in an overheated home works like a waiter alone on a full terrace: it’s not a lack of will, it’s physics.
A poorly executed installation leaves traces: pipes that are too long or poorly insulated, insufficient vacuum before charging refrigerant, incorrect slopes, poor placement of the outdoor unit, inadequate return air, problematic drainage. Many breakdowns are born on the day the equipment is installed, only to manifest months later. It’s the seed under the tile.
The correct temperature doesn’t fix a breakdown, but it avoids punishing the machine
Setting the air to 18 degrees doesn’t turn the living room into Lapland faster. In most units, the compressor will work until it reaches the target temperature, but the cooling rate depends on the power, the state of the system, and the thermal load of the room. A setting that’s too low increases operating hours, electric consumption, and wear, especially if the unit is already dirty or just right in power.
As a reference for comfort and efficiency, organizations and manufacturers usually operate in a range of about 24 to 26 degrees in summer. The IDAE has been a common reference for energy-saving recommendations for years, and manufacturers often insist on a similar idea: lowering the thermostat too much doesn’t always improve comfort, but it can spike the bill. In a real home, with blinds, windows, solar orientation, and human routines, balance is worth more than the heroic number on the remote.
The important nuance: if the air doesn’t cool at all, raising or lowering the thermostat won’t resolve the cause. But reasonable use does help avoid exacerbating it. Keeping filters clean, closing blinds during direct sunlight hours, ventilating early, not blocking the outdoor unit, and not demanding 20 degrees with 40 outside helps distinguish between a unit saturated by extreme conditions and a real breakdown. A house is not a cold storage room. Nor does it need to be.
When to call the technician without overthinking it
There are signs that separate domestic checks from professional territory. If warm air comes out for more than 20 or 30 minutes in cool mode, with clean filters and the temperature properly set, something is off. If ice appears, if the outdoor unit doesn’t start, if the compressor tries to engage and stops, if there’s persistent dripping, electrical smell, error codes, progressive loss of performance, or circuit breaker trips, the solution is no longer in the remote.
It’s also wise to call when the unit is several years old and has never received maintenance. Not for drama, but because dirt may be in areas the user doesn’t see: interior turbine, evaporator coil, condenser, tray, drain. A professional inspection disassembles more than should be disassembled at home and allows for detecting leaks or abnormal consumption before the big summer day arrives, the one when everyone calls the technician at once and discovers that the human schedule also overheats.
Annual maintenance before the intense heat isn’t an installer’s whim. It’s a fairly cheap way to avoid costly breakdowns. In units used daily, homes with pets, commercial premises, or dusty areas, the frequency may be higher. The monthly filter doesn’t replace professional inspection, but it delays it, makes it cheaper, and prevents the unit from working suffocated. Dust, like almost everything small, wins by accumulation.
The age of the unit matters. An old split may lose performance due to compressor wear, less precise sensors, fatigued fans, or dirty exchangers. If the repair budget approaches the cost of a new efficient unit, it’s worth doing the math. Not only for electric consumption but also for refrigerant availability, noise, warranty, and comfort. The heroic repair of a worn-out machine has something noble, yes, but also something of slow ruin.
In a rental property, the situation requires some order: document symptoms, dates, photos of ice or errors, approximate temperatures, and communications with the owner or agency. It’s not enough to say “it doesn’t cool”; it helps to explain that it’s in cool mode, at a certain setting, with clean filters, and that after a certain time the room doesn’t drop. That detail avoids circular discussions, so typical in Spain, about whether “it must be that it’s too hot.”
The cold doesn’t fail suddenly: it warns beforehand
An air conditioner that doesn’t cool rarely breaks in complete silence. It leaves clues first: it takes longer than other summers, expels less air, makes a different noise, drips, smells of humidity, freezes a pipe, raises the bill, only cools at night, or needs many hours to achieve what it used to do in half the time. Those signs are small columns of smoke. Ignoring them works until it doesn’t.
The sensible reading is this: first, rule out the simple — mode, setting, filters, flow, obstacles, outdoor unit — and then suspect the serious: refrigerant, compressor, sensors, electronics, or installation. The user can clean, observe, and adjust. They shouldn’t manipulate gas, open circuits, or improvise electrical repairs. The boundary is not elitist; it’s safety, regulation, and common sense.
The best air conditioner is not the one that turns the house into a portable morgue, but the one that maintains a stable temperature, dries the right amount of humidity, consumes reasonably, and doesn’t call for help every August. When it stops cooling, the unit is saying something. Sometimes it murmurs “clean me.” Sometimes it says “you’ve put me in fan mode, genius.” And other times, more seriously, it warns of a leak or a compressor that’s starting to say goodbye. Listening to it in time is usually the difference between an uncomfortable afternoon and a bill with the ambition of a Russian novel.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine7 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Magazine7 days agoXiaomi launches steam air fryer in Spain for €179.99
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Air fryer7 days agoCecotec air fryer E1 error: what to do safely
Magazine7 days agoMan affected by smoke in Valladolid fire
Heat pump6 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine6 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Magazine4 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















