Dishwasher
Indesit dishwasher errors: codes, lights and safe checks
The code is a clue, not a diagnosis. Your model determines what the warning means and which checks are safe.

An Indesit dishwasher that stops with a warning may have a water supply, drainage, heating or electronic control problem. The meaning depends on the model: F6 generally points to filling and F3 to drainage on ranges that use those indications, but not every machine shares the same code chart. Record the full message before resetting; if there is a visible leak, a burning smell or a tripped electrical safety device, stop using the appliance and arrange a professional inspection.
If you have a problem with your dishwasher, you can use our free error code finder. It can help you identify errors and find information on resolving them easily and effectively.
The model is the key to interpreting the warning
Indesit has sold dishwashers with displays, indicator-light panels and different generations of electronics. A letter followed by numbers, a combination of lights and an audible signal do not form a universal language. To identify the appliance, look for the Mod. reference and S/N number on the rating plate, usually on the inner edge of the door. A photograph of that label and another of the control panel preserve the complete appliance details without taking anything apart.
The way the alarm appears also matters. F03 may be displayed as F3 on certain screens, but that similarity does not justify transferring every meaning between ranges. It certainly does not make A03 equivalent to F03. The deciding reference is the manual for the specific model, particularly when a generic chart links the same number to problems as different as a leak, a thermostat fault or a blockage.
The point at which the cycle stops helps organise the checks. A machine that tries to fill but remains dry gives a different clue from one holding dirty water at the end. Record whether the warning appears at startup, during washing or while draining, and whether a pump can be heard running continuously. These observations are useful, although they cannot identify the faulty part alone.
F codes and H20, including their interpretation limits
The following table brings together associations described for different Indesit dishwasher families. It does not replace the appliance documentation: incompatible interpretations are explicitly flagged. A code reports a detected condition, not necessarily its underlying cause. That is why an alarm does not justify buying parts before the range and diagnosis have been confirmed.
Household checks are limited to the water supply, door closure, filters and visible sections of hose. Inspecting pumps, sensors, inlet valves, the heating element or the control board requires an authorised technician. There is no need to enter diagnostic modes or remove panels to collect the information covered by this table.
| Code | Description | Possible cause or conflicting interpretation | Safe check and limit |
|---|---|---|---|
| F01 | Anti-flood system activated on the relevant ranges. | Water detection or an overflow condition; the source needs investigation. | Do not start another cycle. Close the water supply valve if accessible and arrange an inspection. |
| F02 / F2 | Inlet valve fault in one available code chart. | Other generic charts associate it with leaks. These interpretations are not interchangeable without identifying the range. | Confirm the meaning in the manual. Stop using the machine if there is water outside it. |
| F03 / F3 | Water drainage problem on ranges using this indication. | Blocked filter, kinked hose, blocked household drain or pump fault. | Clean accessible filters and check the visible hose and sink drainage. Pump diagnosis is a technician’s job. |
| F04 / F4 | Temperature control fault in one of the documented families. | Conflicting generic charts also associate it with drainage. | Do not choose between these interpretations without the model manual. |
| F06 / F6 | Filling time exceeded or no incoming water. | Closed valve, insufficient supply, kinked hose, obstruction or filling system fault. | Check the household supply, water valve and visible hose section without disconnecting it. |
| F07 | A warning associated with a turbine in the available technical chart. | The wording does not reliably identify the component without knowing the platform. | Confirm the model-specific description; do not automatically attribute it to the wash pump. |
| F08 / F8 | Required temperature not reached within the expected time on certain ranges. | Possible heating, temperature measurement or control problem. | Do not work on the heater, sensors or connections. Arrange diagnosis if it returns. |
| F09 / F9 | Software or control error on the relevant ranges. | An electronic issue that does not, by itself, prove the control board needs replacement. | A power-off and restart test may be appropriate if the manual allows it and there are no warning signs. |
| F10 | Warning associated with the heating element. | Possible heating circuit fault requiring technical verification. | Stop testing if it returns. Do not access internal components. |
| F11 | Wash pump fault on the documented ranges. | A circulation problem or pump malfunction. | Only check that dishes do not obstruct the spray arms. Pump diagnosis requires a professional. |
| F12 | Communication error between the main module and display on certain ranges. | An electronic communication problem; the code alone does not locate the faulty component. | A reset allowed by the manual may rule out a temporary issue. Recurrence requires inspection. |
| F15 | Interpretation depends on the range. | Listed as a sensor error in one chart and premature cycle completion associated with drainage in another. | Record when the cycle ends and visually check the drain hose route without altering the installation. |
| H20 | Water inlet warning on models using this indication. | A closed valve or insufficient water supply, among other possibilities. | Check the supply and confirm the exact message in the manual. |
The conflicting interpretations of F2, F4 and F15 prevent a single brand-wide definition. If an explanation does not match the observed behaviour, do not force the diagnosis: a dishwasher full of water does not, on that evidence alone, have a broken pump. The right decision depends on code, model and symptom together, not a matching number.
A-series alarms must not be read as variants of F codes
There are A-prefixed alarm charts describing leaks, temperature, water level and control circuits. Without a model reference validating those associations, it is not safe to present them as a universal Indesit chart. Their usefulness is limited: they help establish that this is a different alarm family, not select replacement parts or begin a repair.
This table retains the available interpretations as guidance that still needs confirmation. Relay and triac refer to devices controlling electrical components; these are not accessible parts for household checks. In every case, the specific manual must validate the meaning and internal diagnosis belongs to the professional investigating the fault.
| Code | Indicative description, not universal | Reported cause, requiring model-specific confirmation | Limit of user action |
|---|---|---|---|
| A01 | Possible leak detection. | Float switch activation. | If there is a leak, stop using the machine and close the accessible water valve. Do not tilt the appliance. |
| A02 | Heating control problem. | Heater relay or its circuit. | Technical inspection; not automatically equivalent to F02. |
| A03 | Temperature measurement problem. | Possible short circuit in the thermistor or temperature sensor. | Professional internal diagnosis. |
| A04 | Temperature not reached or not detected. | Heating or temperature detection problem. | Confirm the detection conditions in the model documentation. |
| A05 | Water level or inlet control problem. | Pressure switch does not return to its expected state. | Do not interfere with internal sensors or tubing. |
| A07 | No circulation or spray arm movement. | Wash motor or its electronic control. | Only check for visible obstructions from dishes; the motor requires inspection. |
| A08 | Auxiliary wash control problem. | The relevant triac circuit. | Professional electronic intervention. |
| A09 | Main wash control problem. | The relevant triac circuit. | Do not assume this is equivalent to an F09 software error. |
| A10 | Inlet valve control problem. | Valve drive circuit. | Only check the external supply; internal diagnosis requires a professional. |
| A11 | Half-load or alternating operation problem. | Valve or motor control, depending on the platform. | First confirm which function is affected on the model. |
| A12 | Heating relay problem. | Possible open circuit. | Do not transfer the interpretation of F12. |
| A13 | Dispenser control problem. | Dispenser drive circuit. | Do not dismantle the door or internal mechanism. |
| A14 | Possible instability associated with drainage. | Drain hose positioned too low in the available chart. | Compare visually with the manual; installation corrections belong to a professional. |
There is insufficient basis to apply a fixed heating timeout to every A04 alarm or associate each warning with a particular replacement part. An electrical description does not establish that the entire control board is damaged either. The code defines an investigation; confirmation requires appropriate testing of the affected system.
The IDL 40 indicator lights have their own meanings
The Indesit IDL 40 manual describes alarms through rapidly flashing cycle-stage indicators. This is a model-specific reference and must not be confused with panels carrying 3-, 6- or 9-hour delay markings. Before counting lights, identify the name of each indicator: its physical position can vary between appliances.
A flashing light does not always signal a fault, either. On this model, a flashing drying indicator marks the end of the programme. The distinction between that normal behaviour and an alarm lies in the combination and context described in the manual, not simply the fact that a light switches on and off.
| IDL 40 code or signal | Description | Cause | Specified action |
|---|---|---|---|
| Indicators 2 and 3: wash and rinse, flashing rapidly | Closed water tap alarm. | No supply because the water tap has not been opened. | Switch off, check and open the supply valve if it was closed; wait about 20 seconds before switching on and selecting the programme again. |
| Indicators 1 and 3: prewash and rinse, flashing rapidly | Blocked filter alarm. | Large food particles in the filter assembly. | Switch off, disconnect safely, allow to cool and clean the accessible filter before refitting it correctly. |
| Indicator 2: wash, flashing rapidly | Water inlet valve alarm. | Abnormal operation of the water filling system. | The manual allows switching off and restarting after one minute. If the alarm persists, close the valve, disconnect safely and arrange inspection. |
These combinations must not automatically be converted into F codes using binary charts intended for other panels. A photograph or short video avoids confusion between steady and flashing indicators. If the range is unknown, describing the original signal provides more useful information than assigning a guessed number.
Water not entering and water not draining need different checks
For F6 or H20, where the manual confirms a filling problem, check whether other household taps have water and whether the dishwasher supply valve is open. Inspect only the accessible hose section for crushing or kinks. If reaching it requires pulling out the appliance or disconnecting a fitting, the check is no longer a household task: do not dismantle pressurised water connections.
A blocked inlet filter can also restrict flow, but it should not be confused with the removable filter at the bottom of the wash chamber. The former belongs to the supply connection; the latter traps food residues. Cleaning the internal filter will not necessarily resolve a filling problem, just as opening the tap further will not remove a blockage in the drain.
If the confirmed warning is F3 and water remains undrained, inspect the filter assembly with the appliance switched off, safely disconnected and cool. Use running water and a non-metallic brush on parts the manual permits users to remove. Do not reach blindly into the housing: broken glass may be present. Never run the dishwasher without its filters or with them loose.
Also observe whether the sink drains normally and whether the visible hose section is kinked. A household drainage problem can look like an appliance fault. A hose positioned too low can also affect operation: the IDL 40 specifies a height of 40 to 100 centimetres for the section identified in its manual. That measurement must not be applied to other models or treated as permission to alter connections yourself.
A reset may clear the warning without fixing its cause
For certain F9 and F12 indications, the available documentation allows switching the appliance off and back on after approximately one minute. That test is appropriate only when there is no leak, unusual smell or other warning sign, and when it matches the relevant manual. There is no single reset procedure that applies to every Indesit dishwasher.
On the IDL 40, holding Start/Reset for about 5 seconds cancels the programme selection according to its instructions. Cancelling a cycle and resetting an alarm are different actions: the first changes what the machine is doing; the second may make it possible to see whether an issue returns. Neither proves that the fault has been repaired.
Before clearing the message, save a photograph of the panel and record the stage at which it appeared. If it returns after an accessible check or one reset permitted by the manual, do not run repeated test programmes. A dishwasher starting again does not guarantee that it can complete heating or drainage normally.
With a visible leak or confirmed anti-flood alarm, do not tilt the machine to empty its base or attempt to bypass the float switch. This may temporarily conceal the warning without correcting its cause. Close the water valve if accessible, and avoid touching plugs or connections in a wet area. Professional inspection is required, without further wash tests.
Useful maintenance does not replace diagnosis
Inspecting the filter assembly at least monthly, or every 30 cycles on models whose instructions specify that interval, helps prevent residues from accumulating. The IDL 40 also recommends removing large trapped particles after washing. Frequency should reflect use: dishes carrying thick sauces or small bones leave a different debris load. Correct reassembly is part of cleaning every filter component.
Spray arms need to rotate without hitting plates, handles or long utensils. With the appliance stopped and cool, checking their movement can reveal a loading obstruction without touching internal components. Visible spray holes can also collect residues, but cleaning should follow the manual. A blocked arm can impair washing without proving there is a motor fault.
Limescale, dishwasher salt and rinse aid affect performance and drying, but they do not automatically explain an electronic alarm. Use dishwasher-specific salt and set the softener for local water hardness according to the instructions. The IDL 40 specifies topping up salt approximately every 30 cycles; that is not a universal interval. Adding products indiscriminately cannot replace identifying the actual warning.
The information that prevents guesswork over repairs
If the problem needs professional investigation, provide the model, serial number, warning photograph and point at which the cycle stopped. Describe whether water remains, enters and immediately leaves, or whether the programme finishes early. These details help distinguish installation conditions from internal faults and reduce the risk of choosing a part based only on the code.
A communication or heating warning cannot establish the repair cost. Before authorising work, obtain a diagnosis, an itemised breakdown of call-out, labour and parts charges, and the terms that apply if you decline the repair. Do not assume that the call-out fee will be deducted: this depends on the agreement with the professional, not the appliance brand.
If the appliance may still be under warranty, keep its documentation and check the terms before dismantling it or commissioning outside work. Cleaning user-serviceable filters is not the same as opening the door assembly to access wiring. Age, overall condition and a confirmed quotation help inform repair-versus-replacement decisions; the display number is not enough to make that choice.
The practical boundary is clear: visible supply checks, filters, loading and door closure are accessible checks; pumps, sensors, heating and electronics require authorised diagnosis. Código de Error provides reference information, not repairs or warranty administration. Interpreting a warning correctly means preserving the appliance’s original signal, checking what is safe and not confusing guidance with a proven fault.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Oven6 days agoWhirlpool oven F01 error: what it means and what to do
Coffee machine4 days agoJura coffee machine error 8: what to do and repair costs
Coffee machine3 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine4 days agoSaeco coffee machine error 1: what it means and what to do
Microwave5 days agoSiemens microwave error 1007: what to check and when to stop
Microwave5 days agoError 2 on a Whirlpool microwave: causes and what to do
Oven6 days agoE05 error on a Siemens oven: how to respond safely
Coffee machine3 days agoPhilips coffee machine error 1: causes and safe cleaning
Fridge4 days agoLG fridge FF error: what it means and what to do
Coffee machine4 days agoSaeco error 5: causes and checks without taking it apart
Bosch6 days agoBosch microwave E3 error: causes and safe checks
Beko5 days agoBeko fridge E4 error: what it means and what to do





















