Washing machine
E44 Error in Zanussi Washing Machine: Causes, Diagnosis and Solution
The door lock is usually behind this fault. Here’s how to identify it and check it without wasting time.

The E44 error on a Zanussi washing machine almost always points to the circuit that checks whether the door is actually closed. It is not a decorative fault or a generic alert: the machine protects itself because it cannot safely verify that the door is closed, and therefore blocks the start or interrupts the cycle. In practice, the problem may be in the lock, the wiring, the electronic module or an incorrect reading of the door contact.
If you have a problem with your washing machine, you can use our free error code finder. From there, you can find out about and solve all errors easily and effectively.
What E44 really means
E44 is a door-lock verification fault. The washing machine does not correctly detect the signal confirming that the lock is activated, so the system interprets the load as unsafe. On many Zanussi models, this message appears together with a program lockout, a repeated beeping sound or an abrupt stop just before the drum starts moving.
The logic is simple: without a confirmed door, there is no cycle. The electronics need to receive a stable signal from the lock to authorize filling, spinning and heating. When this circuit fails, the machine does not guess; it stops. This caution prevents leaks, accidental opening and damage to the clothes or the appliance itself.
This warning should not be confused with a purely mechanical problem. Sometimes the door appears to close normally, but the internal microswitch does not change state or does so intermittently. This is where the grey area of this code begins: there is not always a visibly broken part, which is why the symptom can be misleading.
How it appears in everyday use
The fault usually appears at a very specific moment: when selecting a program, pressing start or a few seconds after attempting to start. The washing machine may remain still, display the code on the screen and fail to progress. In other cases, the door appears closed, but the click is not firm or the lock does not activate with its usual sound.
It can also occur intermittently. One wash starts properly, the next one fails and then it works again. This irregularity often points to a worn contact, a loose connector or a lock that still responds but no longer does so reliably. Erratic behavior is a valuable clue because it distinguishes an electrical problem from a simple latch that has not been closed properly.
When the fault originates in the lock, the machine often reacts much like a guard who has not received the correct password: it does not let anything through. If the problem is in the module, however, the lock may work properly and the system may still continue reading an incorrect signal. This distinction marks the difference between a simple inspection and a deeper diagnosis.
Components that are usually involved
The door lock is the first suspect, because it contains both the mechanism that physically locks the door and the contact that informs the control board. If this assembly wears out, overheats or becomes damaged, the circuit does not complete the reading. The most classic symptom is that the door no longer latches as firmly as it used to or that the lock takes too long to activate.
The wiring also deserves attention. A damaged wire, a corroded connection or a terminal that has lost pressure can break the continuity of the circuit. In a washing machine, where there is vibration, moisture and temperature variation, this type of fault is not unusual. The conductor may look fine at first glance and fail only when the machine moves or heats up slightly.
The control module comes into the picture when the mechanical part seems correct. If the lock responds and the wiring is in good condition, the signal may not be reaching the main electronics or may be interpreted incorrectly by them. At that point, we are no longer talking about a door that is simply out of adjustment, but about an incorrect reading in the control chain.
What to check before assuming a major fault
The first check is physical and requires no tools: close the door calmly, without forcing it, and listen for the latch to engage with a clean click. A garment caught in the edge, a misaligned door seal or a loose hinge can prevent the door from closing properly. Sometimes the problem is right in front of you and only requires carefully repositioning the clothes or applying firmer pressure when closing the door.
It is worth listening to how the lock behaves. If the door tries to lock but never actually secures, or if it opens too easily, there is a clear clue. A lock that makes a brief buzzing sound and then leaves the cycle paused is usually trying to activate without succeeding. This sound detail helps distinguish between a poorly closed door and a mechanism that no longer completes its job.
The condition of the frame and the door itself also deserves attention. A previous impact, slight deformation or wear on the latch can be enough to prevent the contact from aligning properly. In a modern washing machine, a few millimeters matter a lot: the electronics require a precise signal, not a reasonable approximation.
Table of faults related to the door circuit
Within the E4 series of codes, several faults are related to the door closing and locking system. Although they do not all mean exactly the same thing, understanding them helps prevent an open contact from being confused with a broader fault.
| Code | Description | Cause | Practical interpretation | Severity |
|---|---|---|---|---|
| E40 | General door or lock fault | Door open, defective lock or damaged wiring | The washing machine does not validate the closure when starting | Medium |
| E41 | Door detected as open | Incomplete closure or contact that does not change state | The system does not receive confirmation that the door is locked | Medium |
| E42 | Problem with the lock | Door lock or defective connections | The machine does not authorize the start | Medium |
| E43 | Lock control error | Fault in the part of the module that controls the lock | The door may close, but the signal is not interpreted correctly | High |
| E44 | Circuit that detects whether the door is closed | Wiring, lock or control module | The system cannot reliably confirm that the door is closed | High |
| E45 | Communication error between module and lock | Connections, control board or lock control | The lock is not managed correctly | High |
What actually tends to fail behind the code
In most cases, the problem starts in the lock or its connections. It is the part that works the hardest and receives the most moisture, heat and vibration. A worn mechanism may continue to appear functional for weeks, but begin to fail when cold, when hot or only with the door in a certain position. This kind of progressive fault is typical of small parts that carry too much responsibility.
If the wiring is broken or the terminal has come loose, the fault can be unpredictable. The washing machine may work after being moved, after closing the door with more force or after being unplugged and connected again. This apparent improvement does not fix anything; it only indicates that the contact is on the edge and occasionally touches where it should.
When the main electronics are involved, the diagnosis already requires more caution. The control module is not usually the first thing to replace, but it should not be ruled out if the door and lock have been checked. On a household appliance, replacing parts without a logical sequence usually makes the repair more expensive and prolongs the problem.
When to stop and request a technical inspection
If the door closes normally, the lock seems to operate and the code keeps returning, the inspection is starting to move into electrical territory. At that point, it is no longer enough to look, listen and reposition things. Continuity checks, connector condition and the reading of the signal coming from the lock to the module are required. Without tools, the margin for action becomes very limited.
You should also stop if you notice a burning smell, abnormal heating or dark marks on the connector. These signs suggest an overload or poor contact, and it is not worth continuing to operate a circuit that is already showing thermal symptoms. Repeatedly forcing the machine to start only adds stress to the control board and the lock.
In homes where the washing machine is opened and closed several times a day, a door fault can become more of an inconvenience than it seems. It does not just prevent washing; it also leaves the user with a machine that appears temperamental. A correct diagnosis avoids the familiar routine of trying programs, unplugging the appliance, waiting and trying again without any real method.
What an accurate reading of the error tells you
E44 does not point to a washing problem, but to an authorization problem. This difference is important because it places the fault before the cycle even begins. The machine is not saying that water is entering incorrectly, that the drum is not spinning or that the heating element is not heating. It is saying something more basic: it does not trust that the door is secured as it should be.
That is why a properly targeted repair saves time and parts. Checking the lock, the wiring harness and the control board in that order is usually the most sensible approach. Intermittent signals, weak clicks and starts that abort immediately are all part of the same technical language. The washing machine does not say much, but when it does, it is worth listening to the exact nuance.
With this type of fault, the difference between a quick solution and an unnecessary repair lies in not confusing the symptom with the cause. A door that appears closed may not be closed as far as the electronics are concerned. And a lock that still makes a sound may no longer be sending the correct confirmation. That is where the heart of the problem lies.
What to remember before replacing parts
The logical sequence is what matters: first the physical closure, then the lock, followed by the wiring and finally the module. Skipping this order leads to unnecessary purchases and incomplete diagnoses. On a Zanussi washing machine, E44 is a specific and fairly useful warning precisely because it narrows down the field of investigation so well.
When the fault is limited to the lock or its connection, the repair may be relatively straightforward. If the problem is on the control board, the intervention moves to another level and requires a more technical assessment. The important thing is not to be led by the first impulse, because this code is rarely solved blindly and almost never improves simply by repeatedly trying to start the machine.
The value of this warning lies in its precision. It does not point to a vague problem or a collection of unrelated faults. It points to a very specific circuit, which makes it possible to move forward methodically. In a machine that depends so heavily on sensors and signals, reading the message correctly is almost half the repair.
When the door seems closed but the machine does not believe it
E44 sums up one of the most frustrating faults in a modern washing machine: everything appears to be in place, but the electronics do not give their approval. This disagreement between what the user sees and what the control board reads turns a domestic routine into a silent wait in front of the panel.
The solution is to restore reliability to the locking circuit, not to keep trying successive cycles or ignore the warning. A lock in good condition, clean connections and a control board that correctly interprets the signal restore normal operation more effectively than any improvised test. In a Zanussi, as in so many modern washing machines, starting depends on a small chain of trust; when one link fails, the system protects itself and stops.
That is why this code deserves immediate attention and an orderly assessment. It is not a whim of the display, but a useful warning that separates a simple incorrect reading from a real fault in the door circuit. Dealing with it methodically prevents further damage and returns the machine to its most basic role: starting and finishing the wash without surprises.
More error codes: Common Zanussi washer error codes and what they mean.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Magazine6 days agoMan affected by smoke in Valladolid fire
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Magazine4 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















