Electrolux
Electrolux washing machine error codes: complete guide
Electrolux alarms help identify faults with filling, draining, the door, the motor and the electronics.

Electrolux Washing Machine Error Codes: Complete Guide
Electrolux washing machine alerts are not there to decorate the display: they indicate a specific anomaly involving water intake, drainage, the door, the motor, temperature or the electronics. When the appliance stops with a code, the machine is translating what has stopped working as it should into a short message.
If you are having a problem with your washing machine, you can use our free error code finder. From there, you can identify and solve all errors easily and effectively.
How Electrolux Interprets Its Internal Faults
Washing machines from this brand operate with a fairly consistent self-diagnostic logic. The code does not always point to a broken part; it often indicates a group of symptoms that requires several parts of the system to be checked at the same time. For example, an E10 may originate from the tap, the hose, the inlet filter or the water inlet valve. The useful information is not just the number, but the area of the circuit where the washing machine has lost control.
On models with a display, the message usually appears directly. On machines without a display, the information is communicated through beeps, flashes or light sequences. This difference changes the way the fault is read, but not its underlying meaning. The electronics protect the wash before the fault becomes worse, which is why the program is often stopped even though the user only notices an inconvenient pause.
The key is to note when the interruption occurred. A blockage at the start is not the same as a stop after draining the water, or an error just before the spin cycle. This timeline greatly reduces the margin for doubt. A washing machine that tries to fill but does not progress points to a water inlet problem; one that remains with the drum full points to drainage; a third that does not even unlock the door is warning of an unsafe closure.
Electrolux, AEG and Zanussi: One Family of Brands, One Fault Language
Electrolux, AEG and Zanussi share architecture, diagnostic logic and many of the same replacement parts. That is why the same code may appear on models from all three brands with the same practical meaning. This compatibility explains why many technicians read these alerts as belonging to a single family, even when the washing machine’s front panel carries a different logo.
The self-diagnostic system was designed to isolate the weak point quickly. It does not provide information as a courtesy; it does so to protect the appliance. If the machine detects that water is not entering, that it is not draining, that the door is not properly sealed or that the mains voltage is unstable, it stops the sequence before a minor fault turns into a more expensive chain of damage.
Excessive Foam as a Possible Cause of a Warning
Excessive foam is another possible cause of a warning or an interrupted cycle. It does not necessarily mean that a component has failed.
Most Common Error Codes and What They Mean
The Electrolux error family is concentrated into a few clearly defined groups:
- E10 and E11: water inlet
- E20, E21, E23 and E24: drainage
- E40, E41 and E43: door
- E50 and variants: motor
- E61, E62 and E66: heating
- E90 onwards: communication between boards and control memory
This organization helps you move from alarm to technical assessment. The most frequent cause is usually simple in water inlet and drainage faults, while electronic alerts require greater caution.
| Code | Description | Cause | Suggested solution | Severity |
|---|---|---|---|---|
| E10 | Water inlet problem | Tap closed, low pressure, blocked inlet filter or kinked hose | Check the water supply, clean the filter and inspect the hose | Low |
| E11 | Fill time exceeded | The tub does not reach the expected level in time | Check the pressure, water inlet valve and inlet filter | Low |
| E13 | Leak detected by Aquastop | Water in the base, damaged seal or internal spill | Disconnect the appliance, dry it and locate the leak | Medium |
| E20 | Not draining | Dirty filter, blocked hose or blocked pump | Clean the filter and check the pump | Low |
| E21 | Draining too slowly | The water drains, but not within the expected time | Check the pump, drain and outlet hose | Low |
| E23 | Drain pump fault | Blocked impeller, damaged pump motor or faulty triac | Electrical inspection and replacement if necessary | Medium |
| E24 | Pump sensor fault | Inconsistent reading from the pumping circuit | Check the wiring, connections and control module | Medium |
| E40 | Door open or not properly closed | The lock does not confirm that the door is locked | Reposition the door and check the door lock | Low |
| E41 | Faulty locking sensor | The system does not receive the correct closure signal | Inspect the lock, wiring and contacts | Medium |
| E43 | Door lock triac | Fault in the electronic control of the lock | Inspect the control board and locking circuit | High |
| E50 | General motor fault | Worn brushes, wiring, motor or power control | Diagnose the motor-control assembly | High |
| E51 | Damaged motor triac | The motor control on the board does not properly control the load | Check the main electronics | High |
| E52 | Tachometer fault | The speed sensor is not reporting correctly | Check the sensor and its fittings | Medium |
| E53 | Inconsistent motor signals | Contradictory readings between the motor and the board | Inspect the connections and module | High |
| E54 | Motor relay fault | The relay does not supply or cut off the current as it should | Check the board and relay | High |
| E59 | Motor does not reach the required speed | The rotation speed does not stabilize | Diagnose the motor, tachometer and electronics | High |
| E61 | Water does not heat up in time | Weak heating element or faulty NTC sensor | Check the heater and temperature sensor | Medium |
| E62 | Water overheating | The temperature control loses its reference and triggers the protection | Inspect the sensor, relay and board | Medium |
| E66 | Heating element relay fault | The relay does not activate or stop the heating | Inspect the control board | High |
| E90 | Communication fault between boards | The interface and main board cannot communicate | Check the connectors, power supply and programming | High |
| E91 | Control board not communicating | Link problem between electronic modules | Inspect the wiring and control panel | High |
| E93 | Incorrect factory configuration | The memory does not match the installed set of parts | Reprogram or adjust the board | High |
| E94 | EEPROM memory fault | The internal memory is damaged | Replace or reprogram the module | High |
| EH0 | Voltage out of range | The electrical supply is reaching the appliance with unstable values | Check the household electrical installation | High |
| EH1 | Unstable mains frequency | Abnormal variations in the current | Check the supply and power outlets | High |
| EH2 | Voltage too high | Overvoltage in the electrical supply | Disconnect the appliance and check the installation | High |
| EH3 | Voltage too low | The washing machine is not receiving enough power | Check the plug and electrical line | High |
What to Do When the Washing Machine Is Not Filling With Water
Filling faults usually have a less dramatic story than they seem to. A partly opened tap, a folded hose or a filter full of sand is enough for the machine to display an E10 or E11. The symptom is clear: the program starts, but the drum does not receive the expected amount of water and the sequence remains incomplete.
When the household supply is working properly, attention shifts to the inside of the appliance. The water inlet valve may be worn, the small inlet filter may have collected sediment or the pressure switch may not confirm that the water level is rising as it should. The washing machine does not work on intuition; it needs consistent signals. If the level reading fails, the entire cycle becomes disorganized before the clothes even get wet.
It is also worth distinguishing between a genuine lack of water and a problem with how the machine interprets the situation. Sometimes water is entering, but so slowly that the control system considers the allotted time to have run out. On other occasions, low water pressure in the home is enough to trigger the alert. This detail explains why two identical machines can behave differently in different homes.
When the Drum Remains Full: Drain, Filter and Pump
The lower part of the washing machine tells many truths. If the cycle ends with water inside, the front filter is usually the first suspect, as it collects coins, lint, threads and small objects. The E20 and E21 codes often appear in these situations because the machine detects that it cannot empty the water quickly enough.
The blockage may be in the filter, the hose or the pump. A coin, compacted lint or a small sock can leave the pump running empty, with that dull humming sound that announces that something is not right.
A dirty filter does not just delay draining: it also puts strain on the pump and extends every cycle. If the washing machine tries to remove the water for longer than normal, the pump motor works under pressure, heats up and eventually loses performance. That is why cleaning the filter regularly is not a household obsession, but a way to prevent a more serious mechanical fault.
When the Washing Machine Does Not Drain or Spin
Drainage is the first line between a proper wash and a drum trapped in dirty water. If the appliance does not drain correctly, it cannot spin normally either, because the safety logic prevents it from rotating at high speed with water inside. That explains why many faults appear to be motor-related when, in reality, they originate below, at the outlet.
The most common pattern begins with E20 or E21. The first indicates a clear failure to drain; the second indicates that the water is draining too slowly. The difference matters because the first case is usually caused by a physical blockage, while the second may point to a tired pump, a partially blocked hose or a drain that is not achieving the expected flow rate.
When the machine does drain but does not spin, it is worth checking how the load is distributed. A duvet pushed to one side, a few heavy items or an almost empty drum can throw the assembly off balance. The washing machine does not rotate decisively because it detects poor balance and protects the bearings and suspension. That pause, which can sometimes be frustrating, is a form of technical caution.
Door, Lock and Safety Alerts
The locking system on a modern washing machine is not just a simple latch: it is a start-up and safety condition. If the washing machine does not receive confirmation that the door is closed, the program will not start. The E40 code indicates that the door is open or not properly closed. Sometimes simply repositioning the latch is enough; at other times, clothing trapped between the seal and the glass or a worn door lock prevents the sensor from confirming the lock.
The E41 code indicates a faulty door-lock sensor, when the lock does not return a valid signal. In these cases, the locking system may need to be checked or replaced.
E43 indicates a fault in the electronic control of the door lock, usually on the board that operates the lock. This type of error requires specialized electronic diagnosis.
Additional Door and Lock Codes: E42, E44 and E45
E42, E44 and E45 also belong to the door and locking fault family. They concern closure faults, safety lock malfunctions or problems in the locking circuit.
A misaligned door gasket is another possible reason why the machine cannot confirm a secure closure and suspends the program.
Additional Motor and Drum Diagnostic Codes
| Code | Diagnostic meaning |
|---|---|
| E55 | Open circuit in the motor. |
| E56 | No data from the tachometer generator. |
| E57 and E58 | Protection against abnormal current draw. |
| EA1 to EA6 | Diagnostics linked to the DSP system and pulley locking or movement. Possible causes include transmission or belt problems, or an inability of the board to validate the spin sequence. |
For E52, a displaced mounting washer is one possible reason why the tachometer signal does not reach the controller. E59 can also indicate a delay in the expected motor signal.
Additional Heating and Temperature Sensor Codes
| Code | Diagnostic meaning |
|---|---|
| E68 | Excessive leakage current. |
| E71 | Abnormal voltage in the temperature sensor. |
| E74 | Incorrect placement of the temperature sensor. |
Oxidation, poor contacts or a badly seated temperature probe can cause thermal faults. These details need to be checked during diagnosis to avoid replacing components unnecessarily.
Electrical and Communication Errors
Codes from E90 onwards are usually related to communication faults between boards and control memory, problems with the electronic interface or faults in the EEPROM memory. These errors are highly serious and generally require the electronic modules to be inspected or replaced.
Codes EH0 to EH3 indicate problems with the electrical supply, such as voltage out of range, unstable frequency or voltage that is too high or too low. In these cases, it is essential to check the household installation to ensure a stable supply and prevent damage to the washing machine.
Other Codes in the Electronics and Communication Family
The electronics and communication group also includes E92, E95, E96, E97, E98, E99, E9a and E5a to E5f. These extend the range of electronic diagnostic alerts beyond the individual codes described above.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Magazine4 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















