Miele
Miele washer error F25: causes and safe checks
A temperature fault can point to the heater, sensor or control system. Learn what you can safely check and when to stop.

When a Miele washer displays F25, it has detected a problem reaching or maintaining the water temperature required for the selected cycle. The cause may involve the heating element, the temperature sensor or the electronic controls; the code alone does not identify which part has failed. Basic checks are safe, but diagnosing or testing internal components should be left to a qualified appliance technician.
If you have a problem with your washing machine, you can use our free error code search tool. There you can identify and troubleshoot errors easily and effectively.
What F25 means on a Miele washer
F25 is a temperature-related fault: the washer has not registered the expected water temperature within the conditions set by its program. Depending on the model and cycle, that may mean the water is not heating as it should, or that the machine cannot reliably detect its temperature. The code is a warning about the heating process, not a precise diagnosis of a single failed part. The exact interpretation can vary by model and control system.
The problem may become noticeable when a wash stalls, takes longer than usual or stops before the cycle finishes. Some models may display the code alongside a warning light or other message, while others may simply interrupt the program. A cold-feeling door or laundry can be a clue, but it is not conclusive: modern washers often use less hot water than older machines, and the glass may not feel warm during every stage of a cycle.
A temperature fault can also be intermittent. A loose or failing sensor, a deteriorating heater, a wiring issue or a control fault may behave differently as the washer warms up and moves through the program. Repeated F25 warnings deserve attention even if the washer completes a cycle after a reset. Clearing the display does not repair the underlying cause.
Why the washer may not reach the selected temperature
The heating element warms water during cycles that require it. If the element has failed, or if its electrical supply is interrupted, the washer may be unable to reach the target temperature. The original troubleshooting information also identifies the thermostat or temperature probe and the electronic control board as possible areas for diagnosis. These are internal components, so checking their connections, resistance or circuit paths is not a safe at-home task.
The temperature sensor, often called an NTC probe, measures how warm the water is and sends that information to the controls. If its readings are inaccurate, the machine may not heat correctly or may report a temperature problem even when the water is warming. A damaged connection or a fault in the control electronics can produce similar symptoms, which is why the displayed code cannot distinguish a sensor problem from a heater or board fault on its own.
Not every interruption means a part has failed. A cycle may behave unexpectedly if it was paused, the washer lost power briefly or the selected program does not heat water in the way a user expects. These circumstances do not confirm the cause of F25, but they are useful context to share with a technician. If the code returns on a normal cycle, treat it as a persistent fault rather than assuming the machine simply needs more time.
Safe checks to make before arranging a diagnosis
Start with observations, not disassembly. Note the exact code, the program in use, when the warning appeared and whether the cycle stopped, drained or continued. Check the care label and selected settings to make sure the program is intended to heat water; many everyday or delicate cycles use lower temperatures. This information can help separate normal program behavior from a genuine heating failure.
If the washer appears to have frozen during a cycle and there is no sign of smoke, a burning smell, unusual heat or water leakage, you can switch it off using its normal controls, wait briefly and restart it once. Follow the instructions in the model’s manual for a reset or canceled cycle. A restart can clear a temporary control interruption, but it cannot restore a failed heater or sensor. If F25 returns, avoid repeatedly restarting the machine.
Check only the areas intended for routine user maintenance. Make sure the door is fully closed and that the drum is not packed beyond the load guidance in the manual. An overloaded drum is not a direct diagnosis of F25, but an unusually heavy load can affect the way a cycle runs. Keep the washer’s accessible detergent drawer and other user-cleanable areas in good condition, following the model-specific instructions. Do not remove panels or reach inside the cabinet to inspect wiring or components.
What not to do when F25 appears
Do not try to test the heater, probe, wiring or control board yourself. Such checks can expose live electrical parts, and measurements made without the right training and equipment can create a shock or fire risk. The original repair guidance refers to checking thermostat connections and resistance, the NTC probe and the circuit board; those are technician-level diagnostic tasks, not routine maintenance. Leave internal electrical testing to a qualified appliance professional.
Do not bypass a temperature sensor, bridge a connection, replace a part based only on the code or continue running repeated hot cycles to see whether the warning disappears. A failed temperature reading can affect how the washer controls heating, and an improvised fix may cause further damage. If you notice a burning odor, smoke, unusual noises, a hot plug or water leaking near the appliance, stop using it and follow the safety guidance in the manual. Do not touch exposed electrical parts or attempt to open the machine.
The safest point to stop troubleshooting is clear: once basic settings and a single restart have been checked, a recurring F25 calls for professional diagnosis. A qualified technician can assess the heater, temperature sensor, wiring and control system using appropriate procedures. There is no reliable repair price or replacement part to infer from F25 alone; the cost depends on the confirmed fault, the model and local labor rates.
How F25 differs from other Miele washer codes
Miele fault codes refer to particular conditions detected by the machine, but their interpretation can depend on the model and product generation. Other codes reported for Miele washers concern water intake, drainage, heating, temperature sensing or motor operation. They should not be treated as interchangeable with F25: a similar symptom, such as a cycle stopping, can arise from entirely different systems. Use the code shown by your own washer rather than borrowing a diagnosis from another model.
The table summarizes common Miele washer codes cited in general troubleshooting material. It is a broad guide, not a substitute for the manual for the exact model. A code may have model-specific details, and symptoms can overlap; for instance, F20 is also associated with heating faults, while F25 points to a problem with the expected water temperature. Check the model manual or have the code confirmed before any repair decision.
| Code | Description | Possible cause |
|---|---|---|
| F1 | Temperature-sensing fault | Possible NTC temperature sensor issue; exact interpretation varies by model. |
| F2 | Temperature-sensing fault | Possible NTC temperature sensor issue; model documentation should confirm the meaning. |
| F10 | Water intake problem | Possible interrupted supply, kinked inlet hose or inlet valve fault. |
| F11 | Drainage problem | The washer may be unable to empty; a blocked accessible filter or drain path is one possibility. |
| F20 | Heating fault | Possible heating element or temperature sensor problem. |
| F25 | Water does not reach the expected temperature | Possible heater, temperature sensor, connection or electronic control issue. |
| F56 | Motor or spin-related fault | Possible motor issue or, in some reports, an unbalanced load; check the model manual. |
When a technician should take over
Arrange a professional diagnosis if the code reappears after a normal restart, if the washer repeatedly stops before completing a cycle, or if laundry remains unexpectedly cold after a program that should heat water. Recurring faults are especially important when they appear alongside a burning smell, unusual sounds or visible leaks. Those signs are reasons to stop using the appliance until it has been assessed.
When describing the problem, provide the full model number and explain which cycle was running, how far it progressed and whether the warning appeared once or repeatedly. Mention any recent power interruption or unusual behavior, but do not attempt to reproduce the fault through repeated cycles. This account can help narrow the diagnosis without exposing you to the risks of opening the washer.
A technician can determine whether the issue lies with the heating element, temperature sensing, wiring or electronic controls. Because those possibilities require different tests and repairs, replacing a component based on the code alone can waste money and leave the original fault unresolved. F25 identifies a temperature problem, while inspection identifies the failed part.
Keeping a temperature fault in perspective
F25 is a useful warning, not a verdict on the washer’s overall condition. It directs attention to the temperature-control process, but it does not show whether a repair will be simple or costly. The machine’s age, model and confirmed failure all matter, and no safe external check can reliably establish the condition of an internal heater or sensor.
For now, the most useful response is measured: confirm the selected program, record when the code appears and try one safe restart only if there are no signs of a more serious problem. If the message returns, stop using repeated resets as a workaround and leave internal diagnosis to a qualified professional. That approach protects both the washer and the person troubleshooting it while keeping the next repair decision grounded in evidence.
More error codes: Miele washing machine error codes: what they mean and what to do.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoSaeco coffee machine error 1: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Coffee machine7 days agoJura coffee machine error 8: what to do and repair costs
Coffee machine7 days agoJura coffee machine error 5: what it means and what to do
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions





















