Heat pump
LG heat pump CH14 error: what it means and what to do
Poor circulation and faulty flow detection can trigger the same warning. Telling them apart prevents unnecessary part replacements.

The CH14 code on LG Therma V air-to-water heat pumps relates to water circulation detection in the hydraulic circuit. It can appear because water is not circulating properly or because the device that checks that movement is not sending the expected signal. The warning alone does not prove that the pump or electronic control board needs replacing. If the fault persists, do not force the system to run: household checks should be limited to the controller, the instructions in the manual and external observations, without opening the unit or working on pipework.
If you have a problem with your heat pump, you can use our free error code finder. It can help you identify errors and find straightforward, effective guidance on resolving them.
CH14 flags a circulation problem, not a specific faulty part
An air-to-water heat pump needs water to move heat from the unit into the heating system. In heating mode, that flow supplies underfloor heating, radiators or fan coils. When the controller does not receive the circulation confirmation it requires, it may stop operation. This is a protective operating condition, not an automatic identification of the failed component.
Two scenarios need to be distinguished with this type of fault. In the first, water really is not moving as required. In the second, water is circulating, but its detection or the transmission of that signal to the controller has failed. Although both can result in a similar display, they require different diagnoses and repairs. Replacing a part based solely on the code can leave the original problem untouched.
The exact meaning and triggering conditions must be checked against the manual for the installed model. Therma V covers different generations and configurations, and they do not all use the same control components. The product range name helps identify the system, but it does not replace the full model number of the units that make up the installation.
The pump, flow detection and controls explain the shutdown
A seized or faulty circulation pump can prevent water from moving around the primary circuit: the hydraulic section the heat pump needs to transfer energy. A pump may also be mechanically capable of operating but fail to receive the correct electrical supply or run command. From outside the unit, both situations can look alike; distinguishing them requires checks that must be carried out by a qualified technician.
The device that detects circulation is another diagnostic checkpoint. Depending on the version, the documentation may describe a flow switch or a flow sensor. Its job is to tell the controller that water is moving. A missing or incorrect signal can trigger the warning without confirming that the circulation pump is faulty.
The electronic control board may also be involved, but it should not become the default explanation before other possibilities are checked. A supply problem, faulty connection or detector issue can produce symptoms that appear to be electronic. Replacing the board only makes sense when the diagnosis can rule out preceding causes and link the fault to that component.
Alongside the components, the technician must assess the hydraulic conditions. A restriction, trapped air or a configuration that leaves insufficient water flow can affect circulation. These are diagnostic possibilities, not causes proven by CH14 appearing. Behaviour following recent work provides context, but it does not establish responsibility or identify the fault without an inspection.
What you can observe without opening the system
The most useful information is often available on the controller. Record the warning exactly as displayed, the operating mode and whether the shutdown occurs at startup or after a period of operation. It also matters whether it happens during space heating or domestic hot water production. That record provides an operating sequence that a photograph of the code alone may not capture.
Use the normal user controls to check that there is a heating demand and that a schedule has not been changed accidentally. If the system has several zones, note whether any remain operational and whether the warning follows particular schedules. Do not change installer settings to experiment: altering settings without understanding their purpose can complicate the subsequent diagnosis and change the system’s hydraulic behaviour.
An external inspection may also reveal damp patches, drips or an unusual reading on an accessible indicator. If there is a pressure gauge, compare its reading with the guidance in your system manual, without dismantling anything. A seemingly normal reading does not prove water is circulating: pressure and flow describe different things, even though both relate to the water circuit.
Sounds provide clues, not certainty. A hum does not confirm that the pump is moving water, and a gurgling noise does not establish where air is trapped. Note whether these sounds are new and when they began, without removing covers or approaching moving parts. The aim is to describe what is happening, not turn an impression of a sound into an instruction to buy spare parts.
A hydraulic filter is not cleaned like an appliance filter
Debris can restrict water flow, so the condition of the hydraulic filter is one possible inspection point. However, a filter being visible does not mean it is safe to open. It may contain hot water and be under pressure. Unscrewing it without the correct conditions creates a risk of scalding and leaks, as well as potentially introducing new problems into the circuit.
When CH14 appears, do not loosen plugs, joints, air vents or connections to see whether water comes out. Do not try to free the circulation pump or work on its connections either. Cleaning hydraulic filters, bleeding the system and any work that requires opening the circuit belong with a qualified professional. They are not equivalent to removing lint from an accessible tumble dryer filter.
The same caution applies to filling the system. Low pressure may require investigation of a leak or an installation issue, rather than simply adding water. Without specific, safe manufacturer instructions for the user, limit your check to reading the gauge. There is no universal corrective pressure that can be recommended for every Therma V installation regardless of its height and configuration.
A reset may clear the warning without fixing its cause
A reset is only appropriate if the model’s user manual allows it and there are no leaks, burning smells or other unusual signs. Follow the stated procedure, without accessing internal electrical compartments or disconnecting components. If CH14 returns, repeated attempts do not provide a new diagnosis: a recurring shutdown indicates that the detected condition remains or is happening again.
A successful restart does not prove that the system is repaired. An intermittent fault may depend on which zones are open, the startup sequence or circulation conditions. Even if heating resumes, keep a record of the warning and watch for recurrence. The temporary disappearance of the code does not justify replacing parts, but neither does it establish that a recurring problem has been resolved.
Do not force heating by bypassing sensors or protective functions. If water is not circulating properly, the unit cannot transfer heat under its intended operating conditions. The shutdown exists precisely to avoid operating outside those conditions. Nor should emergency modes or backup heaters be used as an improvised fix: their availability and operation depend on the installation and they do not necessarily restore flow.
Freezing weather adds an important distinction: stopping a heating demand is not the same as cutting all power to the system. Some frost protection functions require electricity, and their effectiveness may also be compromised by a circulation failure. If CH14 persists in very cold weather, ask the maintenance provider how to leave the installation safe. Do not disconnect power indiscriminately or assume frost protection will continue to work normally.
The exact model prevents confusion with codes from other ranges
Codes displayed on LG equipment should not be interpreted by automatically applying air conditioner information to an air-to-water heat pump. Even within Therma V, the generation and installed combination matter. For technical enquiries, use the accessible identification label or system documentation, and provide the model number of each unit where the system has separate indoor and outdoor elements.
CH14 is the circulation-related warning addressed here. Other codes mentioned in general LG information do not have a description that applies to every model. The following table separates the available information from matters that require model-specific documentation. A cause left unconfirmed is more useful than an invented diagnosis that leads to work on the wrong component.
| Code | Description | Cause | Safe interpretation |
|---|---|---|---|
| CH14 | Warning associated with water circulation detection on Therma V equipment; confirm the triggering conditions in the model manual. | Possible lack of circulation, a circulation pump or supply problem, a flow detector fault or an electronic control issue. | Does not identify the faulty part on its own. Persistent warnings require professional diagnosis. |
| CH01 | Code mentioned in general LG information, without a specific description for the installed equipment. | Not confirmed for the reader’s model. | Consult the exact manual; do not apply meanings from other ranges. |
| CH03 | Code mentioned in general LG information, without a specific description for the installed equipment. | Not confirmed for the reader’s model. | Do not use it to infer the cause of CH14. |
| CH10 | Code mentioned in general LG information, without a specific description for the installed equipment. | Not confirmed for the reader’s model. | Identify the model and its documentation before interpreting the warning. |
Output capacity alone does not establish the hydraulic conditions that must be checked either. A 12 kW installation cannot simply be diagnosed using values from a different model. The minimum permissible flow rate and detection criteria are specific to the model; they should not be replaced with approximate figures found for another unit.
Underfloor heating and hot water provide different clues
In a home with underfloor heating, a cold floor does not locate the fault. The floor stores and releases heat slowly, so its temperature may lag behind events at the heat pump. When describing the problem, linking the code to the controller and schedules is more reliable than relying solely on the perceived floor temperature as evidence of circulation.
Zoned installations add another variable. If the warning coincides with particular zones closing or began after a schedule change, that connection is worth reporting to the technician. It may guide a review of hydraulic control, although it does not prove the cause. Do not open actuators or alter manifolds to investigate: retain known user settings and leave technical adjustments for the inspection.
When the unit also produces domestic hot water, report whether the shutdown occurs while heating the cylinder or when switching back to space heating. Water in the circuit that transfers energy should not be confused with the domestic water delivered at the tap. This distinction helps explain why having a normal household water supply does not rule out a hydraulic fault in the heat pump.
If one function appears to work while another does not, that still does not prove that the valve directing water to each service has failed. It is a clue for checking how circulation changes between modes, not a verdict on a particular part. The most valuable information describes when the fault appears and what the system was doing immediately beforehand.
A repair quote should start with diagnosis, not the code
CH14 does not allow a reliable repair cost to be calculated. Correcting a hydraulic restriction is not the same job as replacing a circulation pump, detector or control board. Without identifying the cause and the component reference, any amount would be speculative. Before accepting replacement parts, the quote should connect the proposed work to the fault that has actually been confirmed and explain what the work includes.
Buying a sensor or pump in advance may seem like a way to save time, but the code guarantees neither that it is needed nor that it will fit. Two visually similar units can use different part numbers. Replacement selection should be based on equipment identification and diagnosis, avoiding trial-and-error part replacement that increases the bill without restoring service.
Callout, travel and diagnostic charges may have different terms from the repair itself. Before authorising a visit, confirm what is payable if the unit is not repaired and whether any charge is credited if you accept the work. If warranty cover may apply, check its terms and the required claims route before commissioning work. Do not assume cover is included solely because of the unit’s age.
A proposal to replace the entire heat pump needs more justification than the appearance of CH14. General condition, repair history, parts availability and the extent of the fault all matter. A localised circulation problem does not automatically mean that the system has reached the end of its life. The comparison should be between specific repairs and alternatives, not between an isolated code and the price of a new unit.
Restoring service means confirming that water is circulating again
A properly targeted repair does not end when the display is cleared. It should establish that the unit operates under the conditions that previously triggered the shutdown and that circulation is detected correctly. If the fault appeared during a change of service or when zones closed, those circumstances belong in the verification. The benchmark is stable restored operation, not just a successful startup at the controller.
For the user, the boundary is clear: observe, document and use only the controls covered by the manual. Opening the hydraulic circuit, testing electrical supplies, handling the detector or working on the control board requires a qualified technician. Keeping the model details, photographs of the warning and the fault context supports a more precise enquiry without unnecessary risks or premature purchases.
CH14 directs attention to water circulation and its detection, but leaves the actual cause open. That distinction avoids two costly mistakes: repeatedly trying to start a system that keeps shutting down and replacing components without proving they are faulty. Repair should follow verification; the code is the starting point, not the complete diagnosis.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions
Air fryer6 days agoE3 error on a Cecotec air fryer: what to do and what to avoid





















