Magazine
My washing machine makes a lot of noise when spinning: causes and solutions
Detect the source of the noise, prevent further damage, and recognize the signs that indicate a serious spin-cycle malfunction.

A spin cycle that thunders like a hammer inside the laundry room is rarely just a simple household nuisance. The intense noise is often a mechanical clue: it may come from an uneven load, poor support on the floor, or internal parts that have already lost alignment, rubber, or lubrication. Ignoring it usually ends up costing more, because the drum spins at high speed and any looseness is amplified with every turn.
The most useful sign is not just the volume of the sound, but its shape. Sharp knocks point to imbalance or damaged suspension; a metallic squeal is usually related to bearings, belt, or internal friction; a deep hum may involve the motor or pump working under strain. From there, the diagnosis becomes more precise and, in many cases, still reversible without a major breakdown.
If you have a problem with your washing machine, you can use our free error code finder. From there, you can quickly and effectively identify and solve all errors.
The spin cycle sound and what it usually reveals
During spinning, the washing machine enters a demanding phase, almost like a car revving up on a short incline. At that moment, any misalignment becomes obvious. The machine vibrates, the drum accelerates, and the suspension assembly, bearings, motor, and structure all endure more stress than during a normal wash. That is why a machine that sounds a bit louder than usual is not always broken, but it is asking for attention.
It is worth distinguishing between normal noise and abnormal noise. A slight motor sound, the thump of residual water, or a mild vibration are within what is expected. The worrying signs appear when the washing machine seems to move on its own, knocks against the cabinet, emits a constant squeak, or gives the feeling that something loose is hitting the inside. Intensity, regularity, and the type of noise are a better guide than any guess.
Context also matters. A new washing machine does not sound the same as one that is more than eight or ten years old. Wear parts such as shock absorbers, seals, bearings, or motor brushes have a limited service life. In homes with several loads per week, that fatigue arrives sooner. The noise during spinning is often the first warning before other faults appear, such as loss of stability, program errors, or an inability to reach speed.
Common causes when the washing machine bangs, vibrates, or squeaks
The most frequent explanation is still the simplest: an unevenly distributed load. A heavy towel next to a few lightweight garments creates an unbalanced mass that the drum tries to correct by banging. The result is a violent wobble, especially visible in the first seconds of the spin cycle. Sometimes all it takes is rearranging the clothes and repeating the cycle; other times, the imbalance reveals that the electronics are no longer compensating as they should.
Another very common cause is an unlevel installation. The washing machine needs to sit firmly on all four feet, with no side-to-side movement or wobble when pressed by hand. An uneven floor, a loose tile, or a poorly adjusted foot can turn a small vibration into a racket. The appliance shifts a few millimeters, hits the wall or furniture, and the noise multiplies like an echo in an empty room.
Objects forgotten in pockets also do their part in sabotaging the machine. Coins, keys, paper clips, metal garment rings, or small screws can become trapped between the drum and the tub, or fall toward the drain pump. In those cases, the sound is usually sharp, intermittent, and metallic. If the noise appears only during part of the cycle, the suspicion of a loose object gains weight. It is not unusual for a button or zipper piece to end up banging around like a marble in a can.
In washing machines with years of use, shock absorbers and suspension springs are common suspects. Their job is to control the movement of the drum and absorb part of the centrifugal force. When they lose effectiveness, the drum bounces, strikes the housing, and the machine moves more than it should. The user perceives this as heavy knocking, especially with medium or heavy loads. This fault rarely appears out of nowhere; it is usually preceded by increasingly visible vibrations.
Worn bearings usually produce one of the most characteristic symptoms: a deep, rough noise, or something like a distant airplane that gets louder as speed increases. These are key parts that allow the drum to rotate smoothly. When moisture gets in, lubrication is lost, or the seal lets water through, wear advances and the sound becomes hard to ignore. At this point, the repair is no longer minor and usually requires technical intervention.
The drive belt can also make noise if it loosens, cracks, or loses tension. It does not always sound like rubbing; sometimes it appears as a high-pitched squeal or irregular slipping. Although it is not the most expensive breakdown, it should be dealt with promptly because a worn belt can affect the drum’s performance and the motor’s behavior. When the machine takes a long time to get going or seems to slip, it deserves a checkup.
Finally, there are less visible but equally relevant problems, such as a tired motor, a clogged drain pump, or the transport bolts not being removed on a new washing machine. The safety screws or bolts used during transport lock the drum to prevent damage during shipping, and if they are not removed before first use, the washing machine can sound as if it were hitting something inside with every spin. It is an easy cause to overlook and, nevertheless, one of the most striking because of how violent the noise is.
How to interpret the type of noise without disassembling the machine
The ear provides more information than it seems. A repeated, rhythmic knock usually points to an unbalanced load, poor damping, or a part touching the tub with each rotation. In contrast, a sharp squeal suggests friction: belt, dry bearing, forced shaft, or a deformed plastic part. If the sound is a low, constant hum, attention should turn to the motor, the pump, or excessive strain in the mechanical assembly.
It also matters when the noise appears. If it is only heard when the machine reaches maximum speed, the problem may be related to drum stability or suspension. If it is already heard when the drum begins turning, the origin may be more basic, such as loose objects or a poorly seated machine. When the noise grows minute by minute, internal wear becomes more likely. And if it is accompanied by a smell of hot rubber or a vibration that makes the appliance move, caution stops being optional.
Another useful detail is frequency. An occasional noise tied to a specific load usually points to poorly distributed clothes or a garment with hard parts. A persistent noise in almost every wash points to a more structural fault. Repetition is the boundary between a setback and a breakdown. Noticing that difference saves time, unnecessary trips, and, above all, poorly targeted repairs.
What to check before thinking about a serious breakdown
There are simple checks that often clarify the situation a great deal. The first is placement. The washing machine must sit firmly, level, and without looseness. If you push it slightly and it rocks like a wobbly table, the problem is right in front of you. Adjusting the feet is usually enough when the floor is reasonably stable. In kitchens or laundry rooms with uneven flooring, an anti-vibration base can help absorb some of the impact and reduce movement.
The second check has to do with the load. If the drum is almost empty or, on the contrary, too full, spinning loses balance. Bulky items such as duvets or blankets absorb water and multiply their weight. An unbalanced load puts more strain on the suspension and makes the motor work worse. Sorting clothes by type and weight reduces the oscillation that ends up moving the whole appliance.
The third check is simple and direct: look in pockets, zippers, fasteners, and small garment parts before washing. A small metal object can sound as if the machine were falling apart, even though it is just banging against the drum. It is also worth checking the drain filter if the washing machine allows it, because some debris ends up there. A coin in the wrong place can imitate the noise of a major breakdown.
If the washing machine is new, a visual check of the transport setup is worthwhile. The drum fixing bolts are usually located at the back and must be removed before first use. Their job is to immobilize the interior during transport. Leaving those anchors in place causes hard knocks, extreme vibration, and the feeling of a poorly assembled machine. It is a more common installation mistake than it seems and should be ruled out before assuming a complex repair.
Burning smell, sparks, or a sudden stop: warning signs
The noise changes category when it appears together with a burning smell, smoke, sparking, or a sudden stop. In that scenario, the washing machine should not be turned on again until the cause is checked. A smell of hot plastic, rubber, or wiring is usually related to the motor, belt, cable harness, or some electrical component overheating. Continuing to use the appliance can worsen the damage and, in the worst case, create a safety issue.
Electrical symptoms also deserve attention. If the display resets, the program cuts out, or the washing machine tries to spin and then stops, there may be a fault in the motor, the control board, or the balance sensors. In these cases, the noise is not the isolated problem but the visible tip of a larger fault. The machine is not only sounding bad; it is also losing control of its own operation.
When the drum turns very little but makes a strained sound, the effort may be coming from a damaged bearing, a blocked pump, or a slipping belt. That friction raises the internal temperature and leaves a very clear trace in the form of smell. Do not confuse that warning with a simple vibration. The combination of noise, heat, and smell calls for an immediate stop.
What it usually costs to repair this type of fault
The repair price depends almost entirely on the source of the noise. Adjusting the feet, removing a stuck object, or correcting poor leveling can cost a small amount, sometimes just the service call or basic labor. Simple repairs usually stay below 60 euros if no major parts need replacing. These are lucky cases, but also the most common when the problem is detected early.
Replacing the belt, shock absorbers, or suspension parts is already a mid-range expense. Depending on the model, access, and labor, the bill is usually between 70 and 150 euros. If bearings, the seal, or drum-related components need replacing, the price can rise quickly because the disassembly is more labor-intensive. In those repairs, the usual range can be from 120 to 250 euros or more, especially in built-in or high-end washing machines.
When the problem affects the motor, the board, or several elements at once, the financial decision stops being trivial. In older appliances, the repair can come too close to the value of a new machine. The age of the appliance, its efficiency, and its overall condition matter as much as the diagnosis. Repairing an eight-year-old washing machine with a bearing fault may still make sense; investing in a fifteen-year-old one with motor and electronics issues requires a colder comparison.
How to reduce noise and extend service life
Prevention is not complicated, but it works. A stable installation is the first barrier against noise. If the floor vibrates, it is worth checking supports, feet, and leveling. An anti-vibration mat can help in homes with hard or slightly uneven flooring, although it does not replace a bad installation. The washing machine should be kept away from walls and furniture so that each vibration does not become an amplified knock.
It also helps to be strict with the load. It is not just about respecting the maximum weight; it is about not concentrating it. Mixing very heavy garments with very light ones can destabilize the drum. Distributing clothes with some logic avoids internal jerks and reduces the strain on the suspension. Just as important is emptying pockets, closing zippers, and using bags for delicate items or garments with metal parts.
Cleaning has its role, although it is often underestimated. The detergent drawer, door gasket, filter, and area around the drum collect moisture, dirt, and soap residue. That film not only smells bad: it also encourages blockages, wear, and unnecessary friction. A clean interior helps the machine breathe and work with less effort. Leaving the door open for a few minutes after each use also reduces trapped moisture.
There is one last habit that makes a difference: listening. Anyone who uses the washing machine every week eventually notices tiny changes in the sound. That household ear is very valuable. If the drum starts to sound different, if the vibration changes, or if the machine takes longer to stabilize, something is evolving. Early detection prevents a small noise from becoming a drum, motor, or suspension breakdown.
When the noise is no longer a simple household annoyance
The line between a noisy washing machine and a faulty one appears when the sound stops being occasional and starts accompanying almost every spin cycle. If the machine moves, bangs, smells hot, or loses power, the problem is no longer cosmetic. At that point, we are no longer talking about a slightly loud appliance, but about a system that is working outside its normal balance.
It is also worth looking at the side effects. A machine that vibrates more than it should can loosen connections, wear down the floor, move nearby furniture, and wear out neighboring parts. It is a kind of mechanical domino effect. Unattended vibration eventually affects more than one part and more than one surface. That is why addressing the symptom early is usually cheaper than waiting for the obvious failure.
The washing machine rarely breaks the silence suddenly without warning first. It repeats the signal, makes it harsher, longer, and more metallic. Anyone who notices the change in sound in time usually gets to a simple repair sooner. And that difference, in such a frequently used appliance, can separate a minor service from a complete replacement of the affected assembly.
When maintenance keeps the drum from talking too much
A well-cared-for washing machine does not need absolute silence to work properly, but it does need stable behavior. The spin cycle should sound like work, not suffering. When knocking, squeaking, or a noise that takes over the house appears, the appliance is telling a story of wear, poor installation, or bad loading. Reading that story in time is the best way to protect both the appliance and your wallet.
The good news is that many cases have a reasonable solution. Sometimes all it takes is repositioning the machine, redistributing the load, or removing a hidden object. Other times, new parts and expert hands are needed. The important thing is not to confuse noise with normality. A healthy spin cycle can be audible; a faulty one, on the other hand, always gives itself away by its excess and its shape.
When the noise becomes a habit, the washing machine is not asking for patience but for a diagnosis. That detail, small in appearance, is often the most profitable of all: observe before the major fault appears. Listening carefully to the machine is, in fact, a form of maintenance.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Air fryer6 days agoE3 error on a Cecotec air fryer: what to do and what to avoid
Magazine4 days agoENISA warns home appliances could be the next cyberattack target





















