Air conditioning
Why your air conditioner is not heating and what to check
A slow start is not always a fault. Settings, airflow and defrost cycles can help explain why the heat has stopped.

An air conditioner running without producing heat is not necessarily faulty: it may be preparing to start, removing frost or operating with the wrong settings. Check that heating is selected and the set temperature is higher than the room temperature. Then let it complete its cycle without repeatedly changing modes. If the lack of heat continues, filters and air outlets are accessible checks; refrigerant and internal components require a qualified technician.
If you have a problem with your air conditioner, you can use our free error code finder. It can help you identify errors and find clear, practical troubleshooting information.
A quiet start can be part of normal operation
In heating mode, many systems keep the indoor fan stopped while the heat exchanger warms up. This is the part that air passes over before entering the room. The delay prevents a cold draught from blowing over the occupants. The unit may have received the remote control command correctly even though there is no noticeable airflow yet: switching on and blowing air do not always coincide.
As a guide, some systems need several minutes, and observing their behaviour for around 5 to 10 minutes may be reasonable, always giving priority to the time specified in the manual. This is neither a universal limit nor a definitive fault test. Outdoor temperature, the previous state of the circuit and model-specific protective functions can affect startup.
Switching off, switching on and alternating between cooling and heating during this wait makes diagnosis harder. Some systems have protective delays and will wait again before starting the compressor. Keeping the command steady therefore helps distinguish a normal delay from a persistent fault. Repeated resets do not repair the underlying cause and may erase useful information from the display.
What matters is what happens next: if warm air starts flowing and the room temperature rises, the startup was consistent with normal operation. If there is no airflow, warnings appear or the unit stops again without supplying heat, note that behaviour. Waiting a few minutes does not mean you should keep testing indefinitely: failure to recover warrants checking the other conditions.
The remote needs to request heat, not just move air
Fan mode circulates room air but does not heat it. Dehumidification mode is not the same as heating either. Look for the heating function on the remote, usually shown by a sun symbol or the manufacturer’s corresponding label. Automatic mode may choose how to operate using its own criteria; when checking this problem, it is clearer to select heating explicitly.
The selected temperature, known as the setpoint, must exceed the temperature detected by the system. If the room is at 20°C and the setting is 21°C, demand is low and a variable-output unit may deliver air that feels less warm than expected. For a brief test, you can choose a setpoint of 24 to 25°C, then return it to a comfortable setting rather than leaving it unnecessarily high.
This increase does not guarantee faster heating or turn the remote into a diagnostic tool. It helps establish whether the system responds to a clear demand for heat. Timers, night schedules and energy-saving functions also deserve attention: a programmed restriction may explain why the system reduces its output or switches off earlier than expected, without there being a fault.
In a multi-split installation, several indoor units share one outdoor unit, and not every system can provide heating and cooling simultaneously. One room requesting cooling may conflict with another requesting heat. Check the model’s limitations and the settings on the other units before blaming a component. Compatibility between operating modes depends on the installed system.
Air needs a clear path to distribute heat
A dust-covered filter acts like a scarf over the air intake: it makes it harder for the system to exchange heat with the room. The air coming out may be warm but limited in volume, so the room takes a long time to warm up. A perceived lack of power does not, by itself, identify a refrigeration circuit fault; sometimes it simply reflects insufficient airflow through the unit.
Home cleaning should be limited to accessible filters that the manual allows you to remove. Stop the unit and follow the manufacturer’s instructions on disconnecting, washing and drying before refitting them. Not all filters can be washed with water or treated with the same products. If access requires removing casings or approaching electrical components, the job is no longer a household check.
Curtains, tall furniture and objects in front of grilles matter too. Check that the louvres are open and positioned using the intended controls, without forcing them by hand. In heating mode, helping the airflow reach the occupied part of the room can improve distribution because warm air tends to rise. An unobstructed outlet helps prevent heat collecting near the ceiling.
A clean filter does not rule out internal dirt or a fan problem. If airflow remains unusually weak at an appropriate fan speed, a professional inspection is needed. Do not run the unit without filters to see whether it improves: removing them as a workaround allows dirt to reach areas that are harder to clean later. The aim is to restore airflow without removing protection.
Defrosting briefly interrupts heating so it can recover
In heating mode, the outdoor unit collects energy from the outside air. Its heat exchanger can become cold enough for frost to accumulate, particularly in cold, humid conditions. To remove it, the system runs an automatic defrost cycle. During this process, it may stop the indoor fan, temporarily reduce heating or make different sounds. This is a planned pause in operation, not necessarily a fault.
On some systems, these cycles last approximately 3 to 10 minutes, but their duration and frequency depend on the model and conditions. Watching whether heating returns afterwards is more useful than timing a rigid limit. An isolated episode is not the same as a permanent loss of performance, and the manual’s specific guidance takes precedence over any general reference.
Water beneath the outdoor unit and a brief cloud of steam can accompany defrosting. They should not automatically be mistaken for a refrigerant leak or smoke. However, a burning smell, electrical crackling or a loud mechanical noise is not explained by normal defrosting: if these signs appear, stop using the system and arrange an inspection without opening the unit.
Frost that clears before heating resumes means something different from a mass of ice that remains or grows. If the system spends much of its time stopped, fails to recover heat or displays persistent warnings, it needs diagnosis. Do not strike the ice, insert tools between the fins or pour hot water over it. Forcing the ice to melt can damage delicate parts and does not address the cause.
Outdoor cold affects performance, but there is no single cutoff
Heating capacity depends on outdoor conditions and the design of the system. As the temperature falls, the heat pump may need to work harder and devote part of its operation to defrosting. However, saying that every unit stops heating at 0°C would be incorrect: each model has its own operating range and a different capacity within that range.
The technical documentation identifies the minimum outdoor operating temperature and the heating output available in cold conditions. These figures are related but not equivalent: a machine being able to keep running does not mean it retains its full output. To assess weak performance, capacity under the actual conditions matters more than an advertised nominal output figure without context.
From a safe position, you can look for leaves, bags or objects blocking airflow around the outdoor unit. Only remove loose obstacles that are accessible without taking off guards or approaching the fan. A unit mounted on a wall or at height is no reason to lean out, climb or work from an unstable position. The check should be visual and free from avoidable risk.
Auxiliary heating is not a feature you can assume is present either. Some systems have a specific backup, while others have no heating element or equivalent function. Its presence and operation must be confirmed in the manual. Activating unfamiliar options or trying button combinations intended for other models does not make up for insufficient capacity and may change settings outside the user’s remit.
Blowing warm air and warming the room are different things
When warm air flows steadily but the room stays cold, look beyond the appliance. An open door to a hallway, draughty windows, high ceilings or poor insulation all increase the heat required. The split system may be heating correctly yet still fail to meet the actual demand. In that situation, the problem is the room’s overall heat balance.
A useful check is to observe its behaviour with doors and windows closed, without extending the area it needs to heat. If comfort returns under those conditions, that points towards heat loss or distribution rather than proving a compressor fault. A single split should not be expected to heat separate rooms evenly either: air encounters physical barriers that rated output cannot remove.
A hand held near the outlet gives an impression, not a reliable measurement of capacity. A system that adjusts its output may maintain the room with moderately warm air rather than always producing the intense stream associated with an electric fan heater. Watch the temperature and comfort level during steady operation. Lukewarm air does not always mean a fault, particularly when the room is close to the setpoint.
Before replacing the appliance with a larger one, the installation, the property’s heat losses and air distribution need assessing. Buying more capacity will not necessarily fix a leak, a blocked filter or an unfavourable location. If the system previously heated the same space well and has clearly deteriorated, that change deserves investigation: sizing alone does not explain a sudden loss of performance.
Refrigerant and reversing valves cannot be diagnosed by touch
Refrigerant circulates in a closed circuit, allowing heat to move between the units. It is not a fuel that should be used up during operation. If the charge is insufficient, a possible leak or an incorrect initial charge needs investigation, alongside other installation circumstances. A loss of performance consistent with low refrigerant does not confirm the cause on its own.
Checking the circuit and carrying out any refrigerant work are jobs for an appropriately qualified professional. Do not connect instruments, loosen joints or touch pipework to look for temperature differences. Besides being hazardous, these isolated checks can lead to incorrect conclusions. When a leak is confirmed, simply adding refrigerant without addressing its source may leave the problem ready to recur.
In reversible systems, the four-way valve changes the refrigerant’s path between cooling and heating. A problem with this valve or its control can prevent the system from heating correctly. Working in cooling but failing in heating directs attention towards the changeover process, but does not prove a faulty valve or rule out every other circuit problem.
There is no need to switch repeatedly between cooling and heating to try to confirm it. Knowing that the system cooled well on a previous occasion can be useful, but it does not replace the technician’s measurements and checks. Before approving a refrigerant recharge or buying a spare part, diagnosis should connect the symptoms, operation and test results. A suspected component is not a diagnosis, even if it features frequently in online explanations.
Fans, compressors and sensors can produce similar symptoms
Seeing the outdoor fan turn does not prove the compressor is working correctly. Equally, finding it stopped for a moment does not confirm a fault: the system may be paused, protecting itself or defrosting. Observation helps describe what is happening, but it does not determine which part should be replaced. The fan and compressor perform different jobs within the system.
A compressor, fan motor, sensor or electronic control fault can reduce or prevent heating. It can also trigger protective shutdowns. Distinguishing these possibilities requires assessment of the specific model and its operating conditions. Do not open covers to check capacitors, connections or circuit boards: internal components require professional attention, even when the unit appears to have stopped.
If a code or flashing-light sequence appears, write it down or take a photograph before switching off. Keep the model reference too, using documentation or an identification label accessible without dismantling anything. The same code can mean different things across brands and product ranges. A warning usually points to a detected condition; it does not always identify the faulty part that needs replacing.
Once settings, normal cycle delays and accessible areas have been checked, a persistent fault warrants a professional visit. Do not keep forcing tests if ice remains, shutdowns repeat or abnormal noises occur. If you notice smoke or a burning smell, stop using the system and avoid touching connections. Whether it can safely keep running depends on the cause; the symptom alone cannot establish safety when the unit is producing little heat.
A clear description helps avoid guesswork repairs
Before the inspection, gather a simple description: the approximate outdoor temperature, the selected setting and when heating stops. It also helps to know whether every indoor unit is affected, whether the issue follows a defrost cycle or whether it started suddenly. These details reveal patterns and make the assessment more useful than a report limited to the absence of warm air.
There is no reliable repair price without identifying the fault, the model and access conditions. Accessible cleaning is a different job from repairing a leak or replacing a compressor. Before approving work, clarify whether diagnosis, the callout and labour are charged separately and what the proposed amount includes. Do not assume the visit is included or automatically deducted from the repair bill.
The repair-or-replace decision should consider the confirmed cause, age, overall condition, parts availability and suitability of the system for the property. An older unit is not beyond repair because of a control fault, and a relatively recent one does not justify every repair regardless of scope. If warranty cover may apply, check its terms before authorising outside work; coverage depends on the circumstances, not a rule inferred from the symptom.
To help prevent performance losses, combine filter cleaning appropriate to usage with the inspections recommended by the manufacturer. A check before the heating season may uncover problems that have remained unnoticed for months. The key is still to distinguish a normal pause from a sustained change: if the system does not recover after the basic checks, the next step is to diagnose the cause before replacing parts or deciding the machine has reached the end of its life.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Magazine3 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Heat pump6 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine6 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Boiler6 days agoImmergas boiler error codes: meanings and safe solutions
Boiler6 days agoViessmann boiler fault codes: what they mean and what to do
Magazine5 days agoENISA warns home appliances could be the next cyberattack target
Heat pump6 days agoLG heat pump errors: 33 CH codes and what to do
Magazine6 days agoCecofry&Crunch: Cecotec’s Air Fryer That Cooks 40% Faster
Ariston6 days agoAriston heat pump fault codes: Nimbus and Nuos explained
Boiler5 days agoBuderus boiler errors: codes and safe checks
Boiler5 days agoBosch boiler faults: error codes, causes and what to do
Boiler5 days agoRoca boiler error codes: meanings and safe checks





















