Boiler
A06 error on Ferroli boiler: causes, signs, and solution
The boiler locks out after starting due to a flame that does not stabilize. These are the causes and the safe check.

The A06 error on a Ferroli boiler appears when the unit completes the ignition sequence but fails to confirm a stable flame. In simple terms: the burner tries to start, the system checks it, and, not receiving a reliable combustion signal, it cuts the operation for safety. In the most common models of the brand, the fault points to a flame detection problem, an incorrect gas-air mixture, or an obstruction in the exhaust of gases.
The issue should not be treated as a simple screen annoyance. When a boiler does not validate the flame, the electronics interpret that combustion is not safe and stop service. In practice, that can leave you without heating and hot water, but it also reveals that something is not working as it should in the ignition, the gas, the flue circuit, or the ionization electrode itself.
If you have a problem with your boiler, you can use our free error code finder. From there you can find out and fix all errors easily and effectively.
What the A06 code really means
In the technical documentation and in the most widely circulated fault lists, A06 is associated with the absence of flame after the ignition phase. It is not a generic failure or a decorative alert: the electronic board orders ignition, waits for flame confirmation, and does not receive it within the expected time. It then blocks the cycle to prevent poor combustion or a dangerous buildup of unburned gas.
The key point is the stability of the ignition. The burner may start the sequence, but if the ionization signal is weak, intermittent, or nonexistent, the boiler understands that combustion has not been established. That detail explains why A06 can appear sporadically on cold days, after a prolonged shutdown, or when the exhaust system is partially restricted.
In the Ferroli ranges most often consulted by users, such as Bluehelix, Modena HE System, and Modena HE Combi, the pattern is similar even though the exact cause may vary slightly. That is why it is best to read the warning as a diagnostic clue rather than a definitive verdict. The same screen shows the symptom; the real fault may be in the electrode, the gas valve, the flue pipe, or the condensate.
The causes most often behind the fault
The most common origin is the ionization electrode. This part verifies that the flame exists and remains steady. If it is mispositioned, worn, dirty, or damaged, the boiler may ignite but fail to confirm combustion. In that case, the unit cuts the sequence even though the start-up appears normal.
A unstable flame also appears frequently, caused by insufficient gas pressure, incorrect valve calibration, or a problem in minimum combustion. When the flame starts weakly and wavers like a match in the wind, the sensor cannot read it clearly and the electronics interpret that ignition has not taken hold. The symptom may worsen if the home has other gas demands or if the installation has a pressure drop.
Another common cause is an obstruction in the exhaust circuit. A dirty, icy, nest-filled, or debris-clogged outlet terminal, a poorly sized flue, or a dirty condensate siphon can alter exhaust and disrupt combustion. The boiler needs to breathe and expel gases cleanly; if that path is disturbed, ignition loses stability and the lockout appears.
How it shows up on the boiler and what signs accompany the lockout
A06 does not always appear alone. In some cases the user hears the start-up attempt, notices an ignition click, and then a brief silence before the code appears on the display. In others, the boiler tries to start several times and shuts off immediately, as if it stumbled on the last step. That repetition is a typical sign that flame detection is not working normally.
The frequency of the fault helps a lot with diagnosis. If the error only appears in extreme cold, the suspect changes: frozen condensate or a partially blocked flue gains weight. If it appears after recent handling or after incomplete maintenance, attention turns to the electrode, component positioning, or gas regulation. If the fault is constant, the electronic board itself or the gas valve deserves a deeper inspection.
In homes with condensing boilers, slow drainage or a sludge-filled siphon can create a misleading scenario. It does not seem like a combustion fault in the strict sense, but the accumulated condensation alters the boiler’s overall behavior and eventually interferes with start-up. The visible symptom is A06; the root cause is sometimes a small dark blockage inside a part nobody looks at until it fails.
What can be checked without taking the unit apart
Before thinking about a more serious fault, it is worth observing two basic elements: gas availability and the general condition of the installation. If other gas appliances in the home do not work, the problem may not be in the boiler but in the supply. On the other hand, if the rest of the appliances respond normally, attention should focus on the Ferroli’s ignition.
It is also useful to check the circuit pressure, even though A06 is not a low-pressure code. An unbalanced installation can affect the start-up behavior. If the circuit is too low or has air in it, the boiler works worse and the combustion process can become unstable. The correct reading, when cold, is usually around 1.0 to 1.5 bar, with a practical value close to 1.2 bar.
In winter, the outside conditions offer very clear clues. Frozen condensate, snow buildup on a terminal, or a partially blocked pipe can cause the boiler to ignite and shut off immediately. It is not uncommon for the error to appear after a very cold night and disappear when the flue regains normal flow. That fluctuation does not eliminate the underlying problem, but it does help identify where to look first.
The technical reference table so it is not confused with other faults
Ferroli catalogs show that A06 shares logic with other combustion warnings, though not the same cause. To avoid confusion, it is worth distinguishing it from codes that affect the fan, water pressure, or temperature sensor. A06 focuses on the absence of flame after ignition, and not on a hydraulic or overheating fault.
The following table summarizes the behavior of the code in different families of the brand and the most cited causes by the manufacturer and by the reference technical manuals. It does not add other errors: it is limited to the systems where this same code appears with a similar reading.
| Code | Model or range | Description | Cause | Technical guidance |
|---|---|---|---|---|
| A06 | Bluehelix Tech | No flame after the ignition phase | Defective ionization electrode, unstable flame, blocked air or flue ducts, blocked siphon or pipes | Check ionization, exhaust, and condensate |
| A06 | Modena HE System | No flame after ignition | Faulty electrode, misadjusted gas valve, unstable combustion, blocked flue circuit | Check ignition and gas adjustment |
| A06 | Modena HE Combi | No flame detected after start-up | Detection electrode, insufficient gas, blocked flue circuit, irregular flame | Check combustion and exhaust |
| A06 | Discontinued Ferroli models | No flame after ignition phase | Ionization problem, gas valve anomaly, blocked chimney, flue, or siphon | Comprehensive ignition inspection |
This comparison makes one idea clear: the same code belongs to the same family, but the fault is read in the details. An A06 on a condensing boiler does not always point to the exact same component as on an older unit. That is why it is so important to pay attention to the full model, not just the display.
Why the ionization electrode weighs so heavily in this code
The ionization electrode works like a tiny guard. It does not heat the house or move water, but it validates that the flame exists and is stable enough to keep the combustion going. If it shifts a few millimeters, becomes dirty with combustion residues, or ages, it can lose sensitivity and generate an incorrect reading.
A worn electrode can produce erratic behavior: one day the boiler starts, the next it locks out, then it works again after a reset. That intermittency is very confusing, because the fault seems to disappear and reappear like a shadow moving from place to place. In reality, the sensor is sending an unsafe or insufficient signal.
Replacement or repositioning of this part should be done by a certified professional, not only because of the work on gas and combustion, but because the fine adjustment determines whether the boiler detects the flame correctly. A poorly installed sensor can turn a quick repair into a recurring fault. In these failures, precision matters more than force.
Gas, combustion, and exhaust: the triangle that supports start-up
When a Ferroli shows A06, the problem is not always in a single part. Sometimes the whole system is working on the edge: gas a bit low, flame not clean enough, flue output pushed to the limit. That triangle of gas, combustion, and exhaust supports ignition, and it only takes one of the points to fail for the boiler to protect itself.
The gas valve may be misadjusted or respond irregularly; the burner may be dirty; the flue may be partially blocked; the condensate path may be reduced; the sensor may be somewhat aged. Each factor on its own might go unnoticed, but together they create a fragile start-up, like a row of dominoes leaning to the same side.
The key is not to confuse symptom with origin. The display does not say why the flame is unstable, it only warns that it has not been successfully verified. An experienced technician will usually check the obvious first, then the ionization reading, and finally the combustion balance. That order avoids changing parts blindly and reduces unnecessary repairs.
What not to do so as not to make the fault worse
Reset after reset does not solve the problem and, in some cases, only masks it. If the boiler keeps returning to the same lockout, it is signaling that the cause is still present. Forcing successive start-ups does not turn the fault into a false alarm; it only makes the unit insist on a maneuver that has already proven to be unstable.
It is also not advisable to dismantle the unit without specific training. Inside a boiler there is a mix of electricity, gas, combustion, and sealing. Safety depends on precisely calibrated parts, and touching one of them without proper knowledge can create a more serious issue than the original. The user can observe, note the code, and check what is visible; internal handling requires certification and method.
If the error coincides with the smell of gas, abnormal noises, or abrupt, immediate shutdowns, caution must be absolute. In that scenario it is no longer a mere household inconvenience, but a situation that requires stopping the unit and leaving the inspection to a professional. A06, when combined with other symptoms, stops being a technical warning and becomes a clear shutdown signal.
What a technician usually checks during a real visit
In a typical service call, the professional starts by confirming the model, reading the code, and observing the start-up behavior. Then they check flame detection, the condition of the electrode, the burner position, and the quality of combustion. If the boiler has condensation, they inspect the siphon, the drain, and the drainage route to make sure there is no silent obstruction.
Later, the gas valve and its adjustment parameters are checked, as well as the flue exhaust circuit. The goal is not to erase the code, but to find the exact point where the sequence loses stability. When the origin is identified precisely, the repair stops being trial and error and becomes a measurable technical intervention.
In older boilers, the condition of the electronic board may also enter the equation, especially if the fault appears erratically or after small voltage fluctuations. It is not always the first suspicion, but it is part of the full picture. A06 is one of those warnings that requires looking at the system as a whole, not as an isolated part.
Why prevention matters more than repeated repairs
The best defense against error A06 is a clean, well-adjusted boiler that is checked regularly. Annual maintenance helps detect a worn electrode, a dirty siphon, a restricted flue, or combustion that is no longer operating finely. They are small details, but in a boiler the details rule like screws in a hinge: they are not very visible, but they hold everything together.
A full service does not just clean. It also checks parameters, verifies exhaust, inspects flame quality, and confirms that the installation has not accumulated air, residue, or misadjustments. In condensing systems, the passage of time leaves its mark in the form of sludge, dampness, and micro-obstructions. If they are allowed to grow, they eventually alter ignition and ionization reading.
That is why A06 often appears in homes where the boiler has worked for months without a tune-up or where winter hits just when the unit is most exposed. It is not just a fault in one part; many times it is the sum of small drifts that end up breaking the stability of start-up.
A fault that speaks of combustion, not just electronics
The A06 error on a Ferroli boiler sends a fairly clear message: the unit has tried to ignite, but has not been able to validate a safe and stable flame. The most likely causes repeat around the ionization electrode, gas regulation, flue exhaust, and condensate. Each points to a different point in the circuit, but all converge on the same idea: combustion has not reached the solidity needed to continue.
That nuance changes the way the fault is read. It is not just a screen with a number, but an active protection that prevents the boiler from continuing to operate in poor conditions. Understanding this makes it possible to act more wisely, avoid mechanical resets, and distinguish what can be observed at home from what requires technical intervention.
When A06 appears, the boiler is speaking in the language it knows best: safety. Listening to it in time is often the difference between a one-off inspection and a fault dragged on for weeks.
More error codes: Ferroli boiler errors: codes and useful solutions.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Magazine4 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















