Daikin
Daikin Altherma 7H error: what it means and what to check
A circulation warning does not identify a faulty part. Pressure readings and when the fault occurs provide useful clues.

A 7H code on a Daikin Altherma means the system has detected a water circulation problem in its hydraulic circuit. Possible causes include trapped air, restrictions, unsuitable pressure, a pump that is not moving water correctly or an inaccurate flow reading. The code does not identify a failed part on its own: before replacing components, the model, full subcode and circumstances of the fault need to be checked.
If you have a problem with your heat pump, you can use our free error code finder. It can help you identify errors and find clear, practical troubleshooting information.
The warning protects heat transfer to the water
A heat pump needs to move water through its heat exchanger to deliver energy to the heating system or domestic hot water cylinder. If circulation is insufficient, the system cannot transfer heat as intended. The 7H warning identifies this condition and may trigger a protective shutdown, depending on the model and operating state.
Heating circuit water should not be confused with refrigerant or the water flowing from household taps. These circuits serve different purposes. Good pressure at the shower therefore does not prove that there is enough flow inside the Altherma, and a 7H warning does not justify adding refrigerant.
The distinction between flow and pressure is crucial. Flow describes how much water is moving, usually in litres per minute; pressure describes a different circuit condition and is generally displayed in bar. A pressure reading can appear normal while circulation remains severely restricted by a blocked filter, a closed valve or a pump problem.
User checks should be limited to the display, any visible pressure gauge and an external inspection of the installation. Opening filters, venting internal components, filling the circuit or dismantling connections involves water that may be hot and pressurised. This work requires a qualified technician following the precautions appropriate to the installation.
The subcode adds detail, but its meaning depends on the model
The 7H indication may be followed by two additional digits. Recording only the first two characters leaves out information that can help with diagnosis. Keep the complete error code, photograph the message where possible and find the unit reference in its paperwork or on an accessible external label.
The variants 7H-01, 7H-04, 7H-05 and 7H-06 appear in connection with circulation faults in documentation for different Altherma systems. However, the same operating context should not automatically be assigned across all models. Precise interpretation requires the manual for that range; a general table cannot replace that model-specific check.
| Code | Description | Cause or context to investigate | Limits of interpretation |
|---|---|---|---|
| 7H | Water circulation fault or insufficient flow detected. | Hydraulic restrictions, trapped air, unsuitable pressure, pump operation or flow detection. | Identify the model and any suffix displayed. |
| 7H-01 | A flow fault variant described as general on certain Altherma models. | The circuit does not meet the circulation conditions required by the controller. | Confirm the description and procedure in the relevant manual. |
| 7H-04 | A subcode within the circulation fault family. | Hydraulic conditions and operating mode associated with this variant on the specific model. | Do not assign an operating mode without checking the documentation. |
| 7H-05 | A subcode within the circulation fault family. | Flow and circuit operation during the condition identified by the controller. | The specific explanation depends on the range and its documentation. |
| 7H-06 | A subcode within the circulation fault family. | Water circulation under the operating conditions defined by the manufacturer for that unit. | Interpret alongside the model and warning history. |
| A6 | On certain Altherma models, a fault associated with the circulation pump. | A blocked pump, hydraulic obstruction or related electrical problem. | It is not automatically equivalent to 7H and does not confirm that the pump needs replacement. |
| E7 | On the ranges described, an outdoor unit fan fault. | A problem with fan operation or speed detection. | Do not confuse E7 with 7H: they require different diagnoses. |
The visual similarity between E7 and 7H can lead people towards repairs that do not apply. Reports about fans, circuit boards or faults following a storm do not, by themselves, explain a hydraulic warning. Reading the characters correctly prevents solutions for a different problem from being applied to the water circuit.
Pressure provides a clue, not proof of circulation
A pressure gauge reading provides useful information without any need to adjust the system. It should be compared with the specified range for the installation and its temperature: cold pressure is not interpreted in the same way as pressure after operation. What matters is the value specified for that system, not a figure taken from another property.
Published general recommendations vary: some suggest cold pressure between 1.0 and 1.5 bar, while others give 1.5 to 2.0 bar. That disagreement means neither range should be treated as a universal target. The height of the installation and its hydraulic characteristics affect the required filling pressure.
A claimed differential pressure of 0.3 bar should not be used as a universal 7H trigger threshold either. Differential pressure, circuit pressure and flow are not interchangeable measurements. The required minimum must be checked in the unit documentation, rather than turning a generic figure into a setting.
If the visible pressure has dropped from its usual value, or falls again after work on the system, tell the technician about that trend. It may warrant checking for leaks, expansion vessel problems or other issues. Repeatedly adding water does not identify the cause and can conceal an ongoing problem; it is not a diagnostic solution.
Filters, trapped air and valves can restrict circulation
A filter loaded with particles creates more resistance to water flow, much like a strainer that has collected too much material. Installation debris, corrosion products and other sediment can build up in a hydraulic circuit. This becomes a reasonable possibility if flow has gradually deteriorated, but the filter should not be blamed without inspection.
Cleaning a hydraulic filter is not equivalent to removing an accessible air filter. Its housing forms part of a circuit that may contain hot, pressurised water. Even if it is visible, opening it requires controlled working conditions. The user can identify its location; a professional should open it.
Trapped air can also interfere with circulation and cause gurgling sounds. If the warning began after building work, maintenance or work on radiators, that history is particularly useful. It does not prove the cause, but it directs attention towards the hydraulic condition of the circuit before the electronics are blamed.
Isolation, zone and diverter valves determine where the water travels. A system can have a heating demand while still providing insufficient flow. It is reasonable to note recent changes, but not to force unfamiliar controls or leave every valve open indiscriminately: the intended system operation must be respected.
When the fault occurs helps narrow the investigation
A 7H warning that appears during domestic hot water production provides a different clue from one that occurs when heating starts. Both involve a circulation problem, but the water route and components involved may differ. Record what the system was doing, without deliberately provoking further tests to reproduce the fault.
If space heating works and the warning appears only when heating the cylinder, the technician can assess the route to that cylinder and the components involved in switching services. This does not automatically mean the three-way valve has failed. The pattern helps narrow down the investigation, not select a replacement part.
It also matters whether the problem began when several heating zones closed. In some installations, room controls change how much water can circulate. Compatibility between zone closures and the heat pump requirements needs to be assessed as a whole; a broken component is not inevitable.
Sounds add context. Gurgling, a new hum or unusual vibration is worth recording, always from outside the unit and without removing panels. However, hearing a motor does not prove that it is pumping correctly, and not hearing it is not enough to condemn it. Its actual performance must be checked.
A reset cannot replace a flow check
The controller may allow a warning to be acknowledged or a user reset to be performed. Only use the operation described in the manual for that model, without entering installer settings. If the message disappears, it shows that the controller has accepted the action, not that the underlying cause is resolved.
If the warning returns, repeated resets will not fix it and may subject the equipment to further operating attempts under the same faulty conditions. Do not bypass protections, change pump speed by trial and error or alter parameters to keep it running. The appropriate decision is to stop forcing the system to operate and arrange an inspection.
Stopping operation at the controller is not the same as disconnecting all power. Depending on the installation, power may be needed for protective functions. Particularly in cold weather, the system should not routinely be unplugged or isolated simply to clear a code; follow the manufacturer instructions.
Water near electrical components, a burning smell or severe mechanical noises change the situation. Do not continue testing, touch wet areas or open covers. These signs require professional assessment and, where there is immediate danger, appropriate emergency assistance, without putting yourself at risk while trying to stop the fault.
The cause must be confirmed before buying a part
A flow sensor may be correctly detecting insufficient circulation or producing an abnormal reading. Distinguishing between these possibilities requires measurements to be compared with hydraulic behaviour. Therefore, 7H is not an instruction to replace the sensor: it identifies a condition that needs investigation.
The same applies to the pump. Air, restrictions, control conditions or an internal fault can affect its performance. Replacing it without checking the circuit may leave the original problem untouched. A sound diagnosis must connect measurements, circuit condition and operation, rather than simply matching a code to a spare part.
Electronics should not automatically take the blame for an intermittent fault either. If the warning coincides with particular services, zone closures or pressure changes, those relationships need examining first. Before accepting an expensive replacement, it is reasonable to ask which check confirms the faulty component.
The exact unit reference also matters when purchasing parts: two units sold under the Altherma name may use different components. Ordering a spare based only on the code can waste money. Until a diagnosis exists, no specific part has been identified and there is no defined repair to quote for.
The cost depends on the diagnosis, not the display message
There is no single price for resolving 7H. Correcting a hydraulic restriction, repairing a leak and replacing a pump are different jobs, even if they produce the same warning. Generic repair figures are not an official tariff and cannot predict the cost for this installation without knowing the cause and model.
A useful quote should distinguish diagnosis, travel, labour, materials and taxes, according to how the professional charges. It is also worth establishing whether the visit is chargeable if no repair is carried out and whether that fee is deducted if the work is accepted. This avoids confusing investigation costs with repair costs.
The code alone does not justify replacing the entire heat pump either. That decision depends on the overall condition, fault history, availability of parts and scope of the confirmed repair. A localised circulation issue does not establish that the equipment has reached end of life.
If warranty cover may apply, review its terms before authorising dismantling or buying components yourself. Not every user observation invalidates cover, but an unrelated intervention may affect the assessment of associated damage. The sensible approach is to document the warning and retain records before any work takes place.
A useful inspection also considers what changed
To prepare for a visit, gather the unit reference, a photograph of the complete code, the observed pressure and the service that was active. Adding when it began and what work was done recently can prevent repeated checks. This information describes the actual fault conditions without interfering with the system.
If maintenance, renovations or changes to room controls have taken place, mention them even if the equipment continued working for a few days afterwards. Some faults appear only when a particular service is requested or demand changes. The sequence of events may be more revealing than a single pressure gauge reading.
Prevention should follow the manual and the characteristics of the installation. Maintenance may include checking filters, circuit water quality, trapped air, valves and the expansion vessel, with professional work where required. It is not appropriate to impose a universal filter cleaning interval or add products without checking compatibility.
After a repair, restoring a normal display is only part of the check. The professional should verify operation under the conditions that triggered the warning and confirm that circulation meets the model requirements. Resolving 7H means restoring the necessary water flow, not simply making the code disappear.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine7 days agoSaeco coffee machine error 1: what it means and what to do
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine7 days agoJura coffee machine error 8: what to do and repair costs
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Coffee machine7 days agoJura coffee machine error 5: what it means and what to do
Coffee machine7 days agoSaeco error 5: causes and checks without taking it apart
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Magazine6 days agoMan affected by smoke in Valladolid fire
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes





















