Miele
Miele washer F138 error: what it means and what to do
A leak-protection warning can stop a wash cycle. Learn what the code signals, what to check safely and when the machine needs professional attention.

On a Miele washing machine, F138 means the leak-protection system has detected water where it should not be, often in the appliance’s base, and activated its AquaStop protection. The washer may stop the cycle to limit further water escape. Treat the warning as evidence of a possible leak, not as a routine reset message: switching the machine off and on will not fix the source if water is still entering or collecting inside.
If you have a problem with your washing machine, you can use our free error code finder. It can help you identify and troubleshoot appliance error codes.
What the F138 warning indicates
The F138 code is associated with water detected by the washer’s leak-protection system. Miele models may use an AquaStop arrangement that responds when water reaches a protected area, such as the base of the machine. The exact components and layout vary between model generations, but the essential message is consistent: the appliance has sensed a potential leak and has interrupted operation as a protective measure.
This does not, by itself, identify the precise point where water escaped. A hose connection, seal, internal water path or another component could be involved, and the fault may not be visible from outside. Nor does the code prove that a large amount of water has flooded the room. It means the protection system has registered a condition that needs attention before normal use resumes.
Some online repair videos show people tipping a washer or removing its panels to drain water from the base. That may make the display change temporarily, but it can leave the original leak unresolved and creates risks from the appliance’s weight, trapped water and electrical components. Do not tilt the washer, open its casing or try to reach the AquaStop switch. The warning is a reason to stop and assess the situation safely, not to bypass the protection.
What to do when the code appears
Stop the cycle and look at the floor around the washer without moving the appliance. If water is spreading, keep clear of wet areas near electrical equipment. If you can reach the water-supply valve safely and it is easy to identify, close it; do not force a stiff or damaged valve. The aim is to limit further water flow without touching wiring, internal parts or the machine’s base.
If the plug and outlet are dry and safely accessible, switch the washer off using its normal controls. Do not handle a plug or electrical outlet with wet hands or while standing in water. If water has reached the outlet, plug, cord or nearby electrical equipment, do not approach or unplug the machine; keep people away and get qualified help. Electrical safety takes priority over clearing the display or saving a wash load.
Once the immediate area is safe, note whether water is visible around the door, detergent drawer, hoses or drain area. These are observations, not instructions to dismantle anything. A damp patch can help a technician narrow down the cause, but water may travel along the cabinet or floor, so the place where it appears is not always where the leak began.
Do not restart the washer just to see whether F138 returns, particularly if there is visible water or the source is unknown. Repeated filling and draining can add water to the affected area. Leave the appliance out of service until the cause has been identified and the protection system can operate normally again.
Possible reasons water reached the protected area
A leak can start at a water inlet or drain connection, a hose, a door seal, the detergent-dispensing path or an internal component. A connection that has loosened, a seal that has worn or been damaged, and debris that interferes with water flow are all possible explanations. These are general possibilities, not a diagnosis of a particular washer; the code alone cannot distinguish among them.
Water may also escape only during one part of a program. A washer can appear dry while idle, then leak when it fills, tumbles or drains. That intermittent pattern can make the problem difficult to trace from outside. A small amount of water left in the base after an earlier leak may also keep the protection active even after the visible floor has dried. A dry floor does not establish that the leak has stopped.
In some cases, the AquaStop system or its sensor may itself need professional assessment. But a user should not assume that a faulty sensor is the cause simply because the appliance is not visibly leaking. The warning could be responding correctly to hidden water, and bypassing or resetting a safety device without finding the reason can expose the home to further leakage.
Safe checks you can make from outside
With the washer switched off and its surroundings dry, inspect only areas that are visible and normally accessible. Look for a kinked, cracked or visibly wet inlet hose, a drain hose that has come loose, water around the detergent drawer, or damage to the exposed part of the door seal. Do not pull the machine out if doing so would strain hoses, scrape the floor or require lifting it. Any check should stop before it involves moving the appliance or removing a panel.
Check whether the door closes evenly and whether fabric or a small item is caught between the door and the gasket. A damaged seal or an obstructed closure can contribute to leakage during a cycle. You can remove visible lint or debris from the accessible surface of the seal, but do not pry at it, apply sealant or attempt to replace it while the washer is installed.
The detergent drawer can be inspected and cleaned if it is designed to be removed by the user according to the model’s instructions. Residue or a buildup of detergent may affect water flow around the dispenser, although it cannot be assumed to explain F138. Do not pour water into the machine to test a suspected blockage, and do not remove filters or covers unless the manufacturer identifies them as user-serviceable and the appliance is safely isolated according to its manual.
These external observations can be useful when reporting the fault, but they cannot confirm that an internal leak has been repaired. If the hoses, seal and visible surfaces look normal while F138 remains, the likely next step is professional diagnosis rather than more home testing.
Why a reset may not solve the problem
A power cycle can sometimes clear a temporary electronic state, but it does not remove water from a protected base or mend a leak. If the code disappears briefly and then returns, that does not show the washer is safe; it may mean that water has reached the sensor again during use. Repeated resets can obscure the sequence of events without addressing the underlying fault.
Only consider a normal restart after the appliance is dry externally, there is no sign of ongoing leakage, and the cause has been addressed or ruled out in a way consistent with the model’s user manual. If the warning returns, stop the cycle and leave the washer off. Do not try to defeat the AquaStop function, hold a switch in place or dry the internal base yourself.
Model-specific instructions matter. Miele washer designs and control systems differ, so a procedure or code interpretation shown for one series may not apply to another. The model identification label and the owner’s manual can help establish which guidance belongs to the appliance, but they do not make internal repair safe for an untrained user.
When a qualified technician is needed
Arrange an assessment by a qualified appliance technician if F138 stays on, returns after a restart, or appears alongside visible leakage. Professional attention is also appropriate if water seems to be coming from beneath the cabinet, the inlet or drain hose is damaged, the door seal is torn, or the machine has stopped mid-cycle with water inside. The technician can inspect the leak path, the AquaStop system and internal components without relying on guesswork from the display alone.
Internal inspection may involve electrical parts, water connections and components that are not intended for user access. Do not remove the front, rear or bottom cover, test electrical parts, disconnect internal hoses or seal a suspected leak with tape or silicone. Once the cause is not plainly visible in an accessible area, diagnosis and repair belong with a qualified professional.
If the washer is under warranty or covered by a service plan, check the applicable terms before arranging work. Keep a note of the model number, the code shown, the program running when it appeared, whether water was visible and any safe external checks you made. This information can help explain the fault; it is not necessary to run another cycle to reproduce it.
How F138 differs from other Miele washer codes
Miele fault codes refer to particular conditions, and their meaning can depend on the appliance family and model. Other commonly discussed codes relate to temperature sensing, water intake, drainage or heating, rather than the leak-protection condition associated with F138. Their appearance in general code guides does not mean they share the same cause or troubleshooting steps.
The table below summarizes the codes described in general Miele washing-machine guidance. It is context only, not a substitute for the manual for a specific model. Do not apply a diagnosis from one code to another, or assume that codes have identical meanings across every Miele range.
| Code | Description | Cause |
|---|---|---|
| F1 | Temperature-sensing fault | Possible issue with the NTC temperature sensor or its circuit |
| F2 | Temperature-sensing fault | Possible issue with the NTC temperature sensor or its circuit |
| F10 | Water-intake problem | Possible interruption to the water supply, a kinked hose or an inlet-valve fault |
| F11 | Drainage problem | The washer is not draining as expected; a blockage or drainage-system fault may be involved |
| F20 | Heating fault | Possible problem involving the heating element or temperature sensor |
| F56 | Motor or spin-related fault | Possible motor issue or, depending on the model and conditions, an unbalanced load |
These brief descriptions are not complete diagnostic definitions. A symptom such as poor draining can have more than one cause, and the same code may require model-specific interpretation. In particular, F10 and F11 point toward water intake and drainage concerns, while F138 specifically indicates activation of leak protection in the washer series to which that code applies.
Reducing the chance of another leak
Routine attention to accessible parts can help reveal wear before it becomes a larger problem. Check exposed hoses and their visible connections from time to time for cracks, bulges, dampness or corrosion, and look over the door gasket for tears or trapped objects. Clean the accessible detergent drawer and seal as directed in the user manual. These checks can catch visible signs of wear, but they cannot rule out a hidden leak.
Use detergent as directed for the machine and avoid overfilling the drum. Excess suds or an overloaded wash can affect operation and put additional strain on the appliance, though neither should be treated as a confirmed explanation for F138. Keep the washer level and ensure its hoses are not sharply bent or trapped, but do not reposition a heavy machine if that means pulling against connected lines.
After any repair, pay attention to the first normal use without putting hands near the appliance or reaching underneath it. If water appears or the warning returns, stop the machine and use the same safety precautions. The important distinction is between routine maintenance of accessible surfaces and repair of the water system: the first may be suitable for an owner, while the second requires the right expertise.
A warning worth taking seriously, not bypassing
F138 is designed to interrupt a wash when the Miele washer’s leak protection detects a potentially unsafe water condition. It does not reveal the exact leak location, and the absence of visible water does not prove that the underlying issue has gone away. Safe external observations may help clarify what happened, but opening the appliance, tilting it or overriding its protection can create additional hazards and leave the leak unresolved.
Keep the washer off if the warning persists, limit access to any wet electrical area and close an accessible water valve only when it is safe to do so. When the source is not obvious or the code returns, have a qualified technician inspect the appliance. Restoring normal operation means addressing the cause of the warning, not merely making the code disappear.
More error codes: Miele washing machine error codes: what they mean and what to do.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Coffee machine6 days agoPhilips coffee machine error 05: what it means and what to do
Magazine2 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Coffee machine6 days agoPhilips coffee machine error 1: causes and safe cleaning
Daikin6 days agoDaikin heat pump error codes: meanings and safe checks
Magazine6 days agoXiaomi launches steam air fryer in Spain for €179.99
Magazine6 days agoMan affected by smoke in Valladolid fire
Air fryer6 days agoCecotec air fryer E1 error: what to do safely
Heat pump6 days agoMitsubishi Ecodan heat pump error codes: causes and fixes
Heat pump5 days agoHitachi heat pump error codes: meanings and safe solutions
Magazine5 days agoHow to Clean a Washing Machine and Fridge: Samsung’s Guide
Magazine4 days agoENISA warns home appliances could be the next cyberattack target
Boiler5 days agoImmergas boiler error codes: meanings and safe solutions





















