Connect with us

Magazine

Gas inspection every 5 years and boiler service every 2 years

Deadlines, costs, who pays and how to avoid fake inspectors in the two compulsory gas checks as the cold arrives.

Published

on

Técnico revisando una caldera de gas en el sótano de una casa

Image: Heiko Ruth / Pexels

The gas installation inspection is carried out every 5 years, and the domestic gas boiler (wall-mounted, up to 70 kW, in a home) is serviced every 2 years. They are two separate obligations, with different people responsible, different prices and different regulations, and it is worth not confusing them as the cold weather arrives.

The first concerns the installation (meter, pipes and valves) and is governed by Royal Decree 919/2006. The second concerns the appliance and depends on the RITE, the Regulation on Thermal Installations in Buildings. Article 7.2 of the gas regulation distinguishes between periodic inspection, for installations supplied from distribution networks, and periodic servicing, for any other case.

Two checks that are not the same

The inspection of a piped gas installation is regulated by ITC-ICG 07, section 4.1, and has a frequency of 5 years. It covers meters, pipes, ducting, valves, combustion and flue gas evacuation, is carried out by the distributor or an authorised company, and is paid for on the gas bill.

Appliance servicing checks that thermal equipment works properly to ensure its energy efficiency, durability and safety. The equipment is not necessarily gas-fired: it also includes aerothermal systems, heating oil boilers and air conditioning. It is carried out by the manufacturer or an authorised installer and is paid to the professional or, if it is a service offered by the supplier, included in the bill. Burners, combustion, safety and control systems, cleanliness and performance are checked.

According to the IDAE, natural gas accounts for 21% of total energy consumption in the residential sector. The OCU reminds consumers that, whatever the type of supply, the installation must be safe and protective measures should be applied to minimise or avoid accidents.

How the gas inspection works

The distribution company, such as Nedgia, Madrileña Red de Gas or Redexis, must give 3 months’ notice that an inspection is due and ensure that it takes place. The inspection checks tightness, pipes, valves and the meter, as well as the state of repair, the combustion of appliances and the correct evacuation of gases.

Since the amendment of section 4.1 of ITC-ICG 07, the inspection can be carried out by the distributor or by an authorised gas installation company freely chosen by the user. There is no obligation to wait for the distributor to take the initiative or to accept the company it proposes. After receiving the notice, the user must ask for quotes and call the technician, who will send the result to the distributor. The autonomous communities keep a register of authorised companies, which is usually on the website of the regional department of industry or of whichever department handles energy.

If the distributor does not receive the documentation from the technician hired, it will send its own staff, giving a few days’ notice. The visit is announced by letter and by notices in the entrance hall or on the staircase, at least 5 days in advance. If the user is absent, the distributor must state the date of a second visit.

How much the inspection costs and who pays

Two charges apply. The distributor’s management fee is fixed at 12.80 euros plus tax and is always payable. The other is the inspection itself: if the distributor carries it out, the price is regulated by the autonomous community and is usually around 30 or 35 euros before tax, according to the OCU, with significant variations: in La Rioja it can fall to 21.50 euros. Distributors such as Nedgia publish their rates on their websites.

The cost goes up if a personal appointment is requested and the scheduled time is not accepted. When the installation is communal, an inspection of the shared part is added, which raises the price by about 10 euros. If you choose your own company, the price is whatever you agree with it, although the OCU notes that it is not easy to find prices lower than the regulated one.

Payment is always made through the gas bill from the supplier, even with your own technician: the technician sends the documentation and the amount to the distributor, which passes it on to the supplier. You should always refuse to pay the technician who carries out the inspection.

In a building with several neighbours, in addition to the individual inspection (Instalación Receptora Individual, IRI), the shared installation (Instalación Receptora Común, IRC) must be checked, and the bill may itemise both. The IRI starts at the meter and covers the pipes, ducting and valves in the home, with a check of combustion and ventilation. The IRC comprises the main pipes, the shut-off valves for each customer, the ducting and the meter cabinets in shared areas, and its cost is shared proportionally among the neighbours.

What happens if the inspection is not done or defects are found

If, after several reminders, the user has not had the inspection carried out, the distributor will cut off the gas supply, since it cannot confirm that the installation is safe. If the problem found is serious, the supply may be cut at the time of the inspection; if it is less serious, a deadline is given to fix it, longer or shorter depending on the defect.

To fix the defects you must hire an authorised installation company, which cannot be the one that carried out the inspection. The user pays for the repair directly and the OCU advises comparing quotes. The professional must provide a certificate and send a copy to the distributor; it is advisable to call to check that it has been reported and to keep the document.

Cylinder, butane and propane installations

Only fixed installations that use cylinders have to pass the inspection; gas heaters and portable cookers do not need it. The check on butane and propane installations (LPG, cylinder or single-user tank) is every 5 years (ITC-ICG 07, section 4.2). It is arranged by the owner with an authorised installation company: the owner must find the professional and pay the agreed price.

In the Basque Country the interval is also 5 years: the 4-year interval came from Decree 28/2002, repealed by Decree 125/2016 of 6 September (BOPV of 13 September 2016), article 3 of which sets the inspection or check every 5 years.

The hoses on butane or propane installations, fixed or portable, have a printed expiry date: check it and make a note of when to replace them. To change one, loosen the clamps, remove the old hose, connect the new one to the nozzles and tighten the clamps firmly.

Service intervals by equipment: the RITE table

The maintenance of thermal installations is regulated by the RITE, approved by Royal Decree 1027/2007 and amended by Royal Decree 178/2021 of 23 March, in force since 1 July 2021. Table 3.1 of IT 3.3 sets the minimum intervals:

EquipmentPowerHomeOther uses
Wall-mounted gas boilerUp to 70 kWEvery 2 yearsEvery year
Gas water heater (DHW)Up to 24.4 kWEvery 5 yearsEvery 2 years
Gas water heater (DHW)24.4 to 70 kWEvery 2 yearsEvery year
Other heating (floor-standing boiler, heating oil, biomass)Up to 70 kWEvery yearEvery year
Air conditioningUp to 12 kWEvery 4 yearsEvery 2 years
Air conditioning12 to 70 kWEvery 2 yearsEvery year
Heat pump for DHWUp to 12 kWEvery 4 yearsEvery 2 years
Heat pump for DHW12 to 70 kWEvery 2 yearsEvery year
Any installationOver 70 kWMonthlyMonthly

The intervals are minimums: they will be at least those indicated, and in all cases the manufacturers’ specifications will be taken into account, so the equipment manual may require a higher frequency. Manufacturers may specify a shorter interval than the legal one: for example, one of them states that its boilers should be serviced annually and that the more frequent the service, the better the appliance performs. In installations of up to 70 kW with continuous remote monitoring, the interval may be extended to two years if safety and energy efficiency are guaranteed.

Who services the boiler, how much it costs and what paperwork remains

Servicing the gas boiler is compulsory and failure to comply is the responsibility of the owner of the installation. The owner commissions it and it is carried out by an authorised maintenance company, registered with the competent body of the autonomous community by means of a statutory declaration; the former authorised companies no longer exist. It covers the appliance: combustion, tightness, expansion vessel, safety elements and flue gas evacuation. For gas appliances, whoever carries out the commissioning, maintenance and repair must also meet the gas authorisation requirements of RD 919/2006. Monitoring compliance is the responsibility of the autonomous communities.

Boiler manufacturers and suppliers sell a maintenance service that includes the check, and it can also be arranged with an independent professional; the price is not regulated. Some manufacturers offer the service from 90 euros within an annual contract that covers labour for possible breakdowns; gas companies charge more, although the service is sometimes more comprehensive. The OCU warns that maintenance is usually an annual service paid monthly, so when changing company or cancelling you should check whether the remaining instalments must be paid, and with older boilers check whether it covers breakdowns.

For installations of up to 70 kW there is an obligation to carry out maintenance but not to sign a contract, which is only mandatory above that power. The contract with the supplier is a voluntary commercial service and does not replace the owner’s legal duty.

Every thermal installation must have a record of maintenance operations, and the owner must keep the documentation on maintenance, repairs, refurbishment and inspections for at least 5 years. For a domestic boiler the technician provides a certificate, which is the document to keep, and usually leaves a label stuck to the appliance with the date. The annual maintenance certificate (article 28 of the RITE) is only required above 70 kW.

Energy efficiency inspections and type B boilers

RD 178/2021 raised the threshold for periodic energy efficiency inspections from 20 kW for heating and 12 kW for cooling to over 70 kW in both cases, with a four-year interval (IT 4.3.1 and IT 4.3.2). According to an explanatory note from the Ministry for Ecological Transition dated 7 March 2022, the powers of the interconnected generators in the same system are added together for that threshold: two boilers of 40 and 35 kW connected to the same manifold are subject to inspection. When the installation is more than fifteen years old and exceeds 70 kW, an inspection of the whole thermal installation is required (IT 4.2.3).

The same royal decree prohibits installing type B gas boilers and water heaters (open combustion chamber) of up to 70 kW, except in rooms that meet the requirements for a plant room or, for water heaters, in an outdoor area in accordance with standard UNE 60670-6. It does not affect type B3x appliances.

Safety at home: carbon monoxide, ventilation and the smell of gas

Poor combustion or a blocked flue can produce carbon monoxide, a colourless, odourless and toxic gas. If there is a non-sealed boiler or water heater in the kitchen, the extractor hood should not be switched on while they are running: they draw air from the room and the lack of oxygen can cause carbon monoxide. Many installations switch the boiler off automatically when the hood is turned on.

Rooms with gas appliances need sufficient ventilation: the lower and upper vents must not be covered and must be kept clean. Boilers and water heaters need a flue with sufficient draught; current models installed indoors have forced draught and it is vital to keep the boiler pressure within the limits of the model. On older water heaters, the pilot flame should be blue and steady; if it is yellowish or flickering it may indicate poor combustion, and it is preferable to switch it off at night.

If you smell gas, ventilate by opening the windows, do not operate switches and contact the distributor’s emergency service, unless the problem is clearly in your own installation, in which case call the technical service. If you are going to be away for a few days, close the main stopcock. Any modification or tampering with the installation must be carried out by a qualified professional.

How to avoid scams by fake inspectors and technicians

The OCU warns that these checks are the target of scams by fake inspectors. It recommends not letting anyone in without identification, never paying the person carrying out the inspection and not letting anyone in without first agreeing what will be checked and the quote.

Warning signs of a scam include turning up without prior notice, not identifying themselves, pressuring with an immediate supply cut or fine, not providing documentation and demanding an expensive repair on the spot without a written quote. If in doubt, check the company’s authorisation with the competent body of the autonomous community and always ask for a written quote and certificate.

This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.

Most read