Kitchen plate
Induction hob not responding: causes and safe checks
A blank display and a cooking zone that stays cold suggest different problems. Check the signs without taking anything apart.

An induction hob that does not respond may have its control lock enabled, moisture on the touch panel or a power supply problem. If the display works but the pan stays cold, the checks are different: cookware compatibility, size and positioning matter. Distinguishing these symptoms helps avoid mistaking an unsuitable pan for an electronic fault. If you notice a crack, a burning smell, a popping sound followed by shutdown or electrical protection devices tripping, stop using the hob and arrange an inspection by a qualified professional.
If you have a problem with your hob, you can use our free error code finder. It can help you identify errors and find straightforward, effective troubleshooting guidance.
A blank display is different from a cooking zone that stays cold
The first distinction is visible. If no indicators appear and the controls give no response, the problem concerns startup or the appliance’s overall operation. An unsuitable pan may prevent heating, but it does not, by itself, explain why the entire panel remains dark. There is little point buying new cookware when the hob shows no sign of activity at all.
When numbers light up, the selected power level flashes or a warning sounds as you place a pan down, at least part of the electronics is responding. Pan detection, a control lock or a protective condition may be involved. The precise meaning depends on the model: a flashing indicator alone does not prove that a sensor has failed or identify a faulty component.
It also matters whether the problem affects the whole surface or just one zone. If a pan that normally works stops heating on only one zone, the cookware becomes a less likely explanation. However, two zones failing on the same side does not automatically identify a particular module either. That pattern is useful diagnostic information, not a reason to open the appliance.
The control panel may be locked, wet or covered
Touch controls need a clear surface and suitable contact. A film of water, food residue or a cloth resting over the controls can interfere with detection or trigger warnings. With the hob switched off and cool, remove objects and clean the accessible surface with a soft, slightly damp cloth. Then dry the panel thoroughly before trying to switch it on again.
There is no need to soak the glass or use harsh cleaning products. Stubborn dirt and detergent residue can make the controls harder to use, but abrasive scrubbing creates another problem: scratches. Follow the manufacturer’s cleaning instructions and keep liquid away from edges and openings. If a substantial spill may have entered the appliance, drying the surface is not enough to rule out damage.
A child lock or cleaning lock may prevent changes to cooking settings or stop the appliance being switched on. Look for the relevant symbol and check the model’s manual for the unlocking procedure. There is no universal button combination or press duration that works across every brand. Holding down several buttons at random may change settings without resolving the control lock.
With dry hands, use the power control as instructed by the manufacturer, without covering other sensors. If the lock symbol disappears and the hob responds normally again, there is no reason to assume that its electronic board is damaged. Persistent unresponsiveness with a clean, unlocked panel, however, warrants a professional assessment, not increasingly forceful pressing.
When there is no sign of power
A supply interruption, a tripped protective device or an internal fault can leave the display completely dark. Check whether the home has electricity and whether other appliances are affected, without dismantling sockets or accessing connections. A working oven or extractor does not confirm that the hob has power: they may be supplied by different electrical circuits.
What happened immediately before shutdown also matters. A general power cut, a recent installation or several appliances operating together provides context, but does not prove a specific cause. If you can see a tripped protective device at the consumer unit, do not remove covers or repeatedly reset it to keep cooking. When tripping coincides with hob use, a professional needs to check the circuit and the appliance.
Connection requirements vary with the appliance’s power rating and design. Some models are designed for 220-240 V supplies, and some configurations require 32 A protection, but these figures are not a universal specification for every kitchen. The appliance documentation and the existing installation determine what is appropriate. Verifying this is the responsibility of a qualified installer, not a user changing wiring or protective devices.
If the hob is new and has never worked correctly, do not assume that a reset is needed or that the pans are to blame. Its installation and commissioning should be checked before further use. Do not lift it out to photograph the underside either: identify the model from the receipt, manual or other available paperwork, without removing the appliance.
A pan can prevent heating even when the controls work
Induction creates heat directly in a suitable pan base using a magnetic field. A cooking zone can therefore be selected yet fail to heat if it does not recognise the cookware. The glass does not need to glow red as it would over a radiant ceramic element. That lack of a glow is normal and does not indicate a fault.
A magnet sticking to the base offers a clue that the material is ferromagnetic, but it does not guarantee that the pan will work well on every zone. The effective base diameter, its construction and the model’s detection requirements also matter. A frying pan can have a wide outer rim while its magnetic base is small.
The most informative check is to use a compatible pan that has already worked on the same hob, centred on an appropriate zone and containing something suitable for a brief cooking test. Do not heat an empty frying pan to test it. If the familiar pan works and another does not, the evidence points towards compatibility or size rather than a general appliance failure.
There is no universal minimum diameter or general rule requiring the pan to be placed before or after switching on. Conventional zones and flexible cooking areas can detect cookware differently. Follow the operating sequence and dimensions in the manual. A warped base or an off-centre pan also deserves attention, but buying cookware without checking first can be an unnecessary expense.
Shutdown during cooking points to a different problem
A hob that starts when cold and stops after high-power cooking behaves differently from one whose display never lights up. Reduced power or shutdown may be associated with thermal protection. However, heat does not explain every interruption: other faults may require professional testing and internal inspection.
If there are no signs of damage, switch the appliance off using its controls and let it cool before using it again as directed in the manual. Ventilation must remain unobstructed, but household checks should be limited to observing accessible areas and moving stored items that block manufacturer-provided air openings. Do not dismantle drawers, panels or the appliance to reach the cooling fan.
No single ventilation clearance applies to every hob. Required gaps and compatibility with cabinets or other appliances depend on the installation drawing. Repeated shutdowns, particularly following refurbishment or furniture changes, call for an installation check. Always cooking at a lower setting to avoid the fault does not address its cause or establish that continued use is safe.
Error codes need a brand and model to mean anything useful
An error code helps narrow down a condition detected by the appliance, but it does not always identify the component that needs replacing. The same combination can mean different things across manufacturers and even between ranges from one brand. Before interpreting a warning, record the full code and model, including characters that appear alternately on the display.
The following examples appear in the available reference cases, but those cases do not provide enough technical documentation to confirm every cause. In particular, a generic claim linking E1 to Bosch electronics cannot safely be treated as a diagnosis for every model. The table separates the reported symptom from the cause to avoid component replacement based on an unverified code interpretation.
| Code | Brand and model cited | Description | Cause | Safe action |
|---|---|---|---|---|
| E1 | Bosch, model not identified | A warning attributed to an electronic problem in a generic reference, without confirmation for a specific range. | Unconfirmed. The code alone does not establish that the electronic board needs replacing. | Check the model’s manual and arrange diagnosis if the warning persists. |
| E5 | Foster FI-903 | A reported case in which the right-hand cooking zone could not be used. | Not specified in the available information. | Record the warning and affected zone; do not apply interpretations from other brands. |
| E6 | Foster FI-904-1 | A fault case with a visible code but no technical definition provided. | Not confirmed in the available information. | Request an interpretation specific to this model without working on internal components. |
| E5 | Kuppersbusch EKI 307.1M-93 | A warning appearing after electrical protection tripped, leaving the hob unusable. | Unconfirmed. Its appearance alongside the trip does not identify the failed component. | Stop using the appliance and arrange professional inspection of the hob and its supply. |
Photographing the warning without touching hot areas preserves the information if it disappears after shutdown. Note whether it occurred at startup, when selecting a zone or after cooking for a while. That context is more useful than a rushed interpretation. A code accompanied by electrical tripping requires inspection before further use, even if the warning subsequently disappears.
A reset does not replace proper fault assessment
Switching off and back on at the controls may clear a temporary control condition if the manufacturer allows this and there are no danger signs. The procedure and waiting period depend on the model; no universal interval guarantees a reset. If the hob responds again, check that operation remains stable during normal use.
If the manual requires the power supply to be interrupted and the hob is hardwired, do not access wiring or search for a concealed connection. Household checks stop where the electrical installation begins. Extension leads, adapters and alternative sockets must not be used to test a built-in hob either. A reset never justifies an improvised electrical connection.
A warning disappearing does not prove that its cause has been resolved. If it returns under the same conditions, retain that information and avoid repeated attempts. Recovering a few minutes of operation may conceal an intermittent fault rather than fix it. When an appliance only works after successive resets, that repetition is itself a symptom requiring diagnosis.
Cracks and electrical warning signs mean stopping use
A crack in the glass changes the priority, even if the cooking zone still heats. Liquids can pass through the damaged surface and reach internal parts. Do not keep cooking on another zone or cover the crack to continue using the appliance. Stop using it and avoid pouring water over it for cleaning; the glass needs professional assessment and replacement if necessary.
A surface scratch is not necessarily a crack, but if you cannot distinguish between them, do not test the appliance to see whether it holds up. A fracture can be fine and difficult to spot in certain reflections. Do not press on the glass or apply household adhesives either. The decision depends on the integrity of the surface, not simply on whether the display still switches on.
A burning smell, smoke, a popping sound followed by shutdown or repeatedly tripping protection devices rule out cooking tests. Do not open the casing or try drying internal components with a hairdryer: electrical risks may remain even after switching off. Avoid touching the appliance and arrange an authorised inspection. If there is a fire or immediate danger, contact the emergency services.
A clear diagnosis should come before paying for repairs
A blank display does not provide a sound basis for quoting an electronic board replacement. The cause may lie in the controls, supply or other parts that only professional checks can distinguish. Do not buy a module because an online error code seems to match: compatibility depends on the exact reference, and a new part does not prove that the old one caused the problem.
Without the model, confirmed cause and scope of work, no reliable repair price can be given for this symptom. When assessing a quotation, establish what diagnosis has been confirmed and what the amount includes. Call-out, testing, labour and replacement parts may be charged differently; the visit fee is not always deducted from a subsequent repair.
Whether to repair or replace depends on overall condition, age, part availability and the total cost compared with an equivalent installed replacement. An isolated fault in a well-maintained appliance presents a different decision from damaged glass combined with recurring failures. Compare complete solutions, not just components, rather than applying a universal percentage threshold.
If warranty cover may apply, keep the receipt and check the terms before authorising work or buying parts. Opening the appliance yourself adds risk and can complicate assessment of a claim, although it would be wrong to state that every right is automatically lost. The prudent approach is to document the fault without dismantling and arrange assessment through the appropriate channel.
The most useful checks stop before the hob is opened
Safe checks distinguish several quite different situations: locked controls, surface moisture, an unrecognised pan or a complete lack of response. If accessible cleaning, the manufacturer’s unlocking procedure and a known suitable pan restore operation, watch for recurrence. There is no need to turn an isolated incident into preventive replacement of components.
When the hob remains dark, the same zone repeatedly fails or shutdowns keep occurring, the information gathered supports professional assessment. The brand, model, displayed warning, affected zone and timing describe the problem accurately. Mentioning that it began after installation or a power cut also helps, without presenting those coincidences as proven causes.
The boundary is clear: cleaning and checking normal operation are not the same as diagnosing the inside. Connecting wires, testing components, removing modules or investigating electrical protection devices belongs to qualified personnel. Recognising that boundary avoids speculative spending and tests that may make matters worse. The aim is not to make it switch on once more, but to restore safe, reliable operation.
This article contains affiliate links: if you buy through them, we earn a small commission at no extra cost to you. More information.
Magazine6 days agoReplacing boilers with heat pumps: CAE multipliers up to x6
Magazine1 day agoWashing machine smells? Clean the seal and leave the door open
Dishwasher7 days agoIndesit dishwasher errors: codes, lights and safe checks
Oven6 days agoSiemens oven error codes: meanings and safe solutions
Fridge6 days agoLiebherr refrigerator errors: codes, alarms and solutions
AEG6 days agoAEG tumble dryer error codes: what they mean and what to do
Dishwasher7 days agoHaier dishwasher error codes: meanings and solutions
Candy7 days agoCandy tumble dryer error codes: warnings and safe checks
Oven6 days agoSamsung oven error codes: meanings and safe solutions
Magazine5 days agoGas inspection every 5 years and boiler service every 2 years
Drying machine6 days agoLG dryer error codes: meanings and safe checks
Coffee machine5 days agoSaeco coffee machine errors: codes, causes and solutions





















